Showing results 3201 - 3250 of 4973
Image
Image
Seal the drywall to top-plate seams and the lower edge of baffles to the top plate to prevent the air coming from soffit vents from flowing under baffles into insulation.
Image
Seal the roof deck as follows: Sweep roof decking, tape seams, and cover underlayment or roofing felt as shown.
Image
Sealant is installed to air seal along the top and bottom plates of exterior walls and along both sides of the first interior stud on intersecting interior walls
Image
Image
Image
Image
Image
Image
Image
Image
Seams in the ICF block are sealed so the EPS foam surface can serve as the drainage plane; no house wrap is needed.
Image
Second layer of rigid insulation is adhered with foam
Image
Section view of a deep pile foundation system constructed with reinforced concrete beams and columns to create portal frames, adapted from FEMA P-550, 2nd ed., case FEMA P-550, 2nd ed., case H.
Image
Section view of a steel pipe pile with concrete column and grade beam foundation type, adapted from FEMA P-550, case B.
Image
Section view of duct or pipe penetration through exterior wall showing flashing and air sealing details
Image
Section view of electric box installation in exterior wall showing flashing and air sealing details
Image
Secure bookcases to the wall with L brackets to prevent damage during seismic events.
Image
Seismic Map of the 2018 International Residential Code adapted by FEMA to show Seismic Design Categories in color
Image
Image
Image
Self-adhering bituminous membrane covers the entire roof of this cold climate home, a practice common under metal roofs and also on complicated roofs
Image
Self-locking drawers and cabinets can be installed to protect against damage from seismic events.
Image
Separate exhaust fans can share a common exhaust if each exhaust fan is equipped with a back-draft damper to prevent cross contamination
Image
Seperate dwellings with their own seperate exhaust terminations
Image
Image
Seven categories of exterior window shading attachments, identified on the DOE Efficient Window Coverings website.
Image
Shade trees planted on the east or west sides of a house are one of the most effective measures that can be taken to reduce heat gains
Image
Shear Strength Comparison Between a Foundation Stud Anchor (on left) and a Shear Transfer Angle (on right)
Image
Image
Shear wall hold-down connector with bracket attached to a wood beam for a home built on a pile foundation.
Image
Sheathing is removed from a flat roof to retrofit with air sealing, insulation, and water control layers
Image
Shed roofs provide more space for PV panels in this multifamily project near Denver, Colorado.
Image
Sheer shades can provide very effective daylighting and glare control while maintaining a softened view to the outside
Image
Image
Image
Sheets of phase-change material are installed over the cellulose insulation to help even out interior temperatures.
Image
Shingle blow-off often starts at the eaves, as shown here after exposure to 115-mph hurricane winds.
Image
Show potential buyers your energy-efficient features with cut-aways and side-by-side displays (Source: Tommy Williams Homes).
Image
Showering accounts for 1.2 trillion gallons of water per year in the United States.
Image
Shrubs, trees, and herbs create a tight network of roots and stems that bind the soil and slow the flow of water down hillsides.
Image
Side and plan views of window-to-wall interface in masonry wall retrofit including three layers of rigid foam exterior insulation, box extensions, and flashing around new windows.
Image
Side by side comparisons of standard roofing colors (top row) and cool colors (bottom row) shows that solar reflectance (R) can be reduced significantly using special coatings with almost no change to the color
Image
Side view showing air-sealing and rigid foam insulation is installed over existing wall and ceiling under a room above, then covered with new gypsum board.
Image
Side view showing how the existing garage wall and ceiling are air-sealed prior to installing rigid foam insulation on the garage side of the shared wall of an existing home.
Image
Siding has been removed so cellulose insulation can be dense-packed into the exterior walls of this home
Image
Simple Integrity built this custom for buyer home in the cold climate in Cooperstown, NY, and certified it to DOE Zero Energy Ready Home specifications in 2020.
Image
Simplified schematic of a one-pipe steam system showing the main and risers with fast vents and the radiators with slow vents
Image
Single framed wall converted to double wall and insulated with closed-cell spray foam
Image
Single framed wall converted to double wall and insulated with closed-cell spray foam and loose-fill fibrous insulation