BASC Search | Building America Solution Center

Install wood framing cross pieces in the attic rafter bays on each side of the duct chase

Image

Wrong: Ducts are not laid across the lower truss cords or ceiling, but are hung from the rafters by straps. As a result, ductwork is not buried

Image

Two pieces of flex duct are spliced together with a metal sleeve, nylon draw bands, mastic, metal tape, and more mastic

Image

Unvented, Insulated Crawlspaces

Guide

Guide describing method for insulating an unvented crawlspace or conditioned basement with rigid foam on the interior side of the walls.

Cut fiber board with a red V-groove tool and a gray shiplap tool to create mitered corners and a shiplapped edge for duct sections

Image

Right - The rigid metal HVAC ducting is installed between the floor joists rather than in an unconditioned attic or crawl space to minimize heat loss.

Image

Right – R-25 of open-cell spray foam lines this new home’s attic ceiling, to protect HVAC ducts from heat and cold.

Image

Step 5. Install sheathing tape flashing over the duct or pipe and wood blocking on either side for later attachment of trim.

Image

Why Are Attics Insulated With Open-Cell Spray Foam So Damp?

Presentation

Presentation describing issues with condensation in unvented attics insulated with open-cell spray foam.

A second layer of rigid insulation is installed over the 2 in. by 4 in. retaining strip

Image

Blown Insulation for Existing Vented Attic

Guide

Guide describing how to insulate a vented attic in an existing home using blown insulation added to the attic floor.

Seal all joints and seams in the metal ductwork with mastic before installing insulation

Image

Attic Air Sealing, Insulating, and Ventilating for Ice Dam Prevention

Information Guide

Information guide describing proper attic air-sealing, insulation, and ventilation to combat ice dam formation on roofs in cold climate zones.

Right- This flue pipe has been air sealed with sheet metal and fire-rated caulk and an insulation dam has been constructed to keep insulation from touching the hot flue pipe

Image

Batt Insulation for Existing Vented Attics

Guide

Guide describing how to increase insulation in existing homes by installing batt insulation on the ceiling plane of a vented attic.

Form an insulation dam of heat-resistant insulation with at least 3 inches of clearance around a flue pipe in the attic after air sealing around the pipe with sheet metal and fire-rated caulk or canned foam

Image

Wrong: This exhaust fan duct is too long and terminates in the attic instead of going through the roof and it is improperly supported; it needs straps all along its length to prevent sagging.

Image

Air Sealing, Insulating, and Venting Attics and Roofs to Reduce Heat Gain

Information Guide

Information guide providing links to guides describing specific ways to air-seal, insulate, and ventilate attics and roofs to minimize heat gain in new and existing homes.

Spray Foam Insulation Applied to Existing Attic Floor

Guide

Guide describing how to apply spray foam insulation to the floor of the attic in existing homes.

Attic Eave Minimum Insulation

Guide

Guide providing guidance on insulating attic eaves in new and existing single-family homes and multifamily buildings.

The inner liner of the flex duct is fastened to the collar with a tension tie, the connection is sealed with mastic, then the outer layer is pulled over and sealed with mastic or foil tape (Steven Winter Associates 2013).

Image

Unvented Conditioned Attic with Spray Foam Insulation Below Roof Deck

Guide

Guide describing a method for insulating an unvented attic by spraying foam insulation along the underside of the roof deck.

Right - The energy recovery ventilator ducts supply filtered outside air to multiple locations in the home and continuously exhaust stale air to provide clean, balanced ventilation.

Image

Monitoring of Unvented Roofs with Fibrous Insulation, Diffusion Vents, and Interior Vapor Control in a Cold Climate

Reference

Report detailing a three-winter study on unvented roof assemblies in a cold climate, assessing insulation material, ridge diffusion vent presence, vapor control membranes, relative humidity, and interstitial airflow. Results indicate that utilizing air-permeable fibrous fill insulations in unvented...

Monitoring of Unvented Roofs with Fibrous Insulation, Diffusion Vents, and Interior Vapor Control in a Cold Climate

Reference

Report detailing a three-winter study on unvented roof assemblies in a cold climate, assessing insulation material, ridge diffusion vent presence, vapor control membranes, relative humidity, and interstitial airflow; results indicate that utilizing air-permeable fibrous fill insulations in unvented...

Air Sealed, Insulated Basements

Guide

Guide describing how to insulate a basement to improve the overall thermal performance of the building and provide more dry, usable conditioned space for home occupants and HVAC equipment.

The attic is sealed and insulated along the underside of the roof deck with 5.5 inches of polyurethane spray foam, providing conditioned space for the HVAC system.

Image

Insulating Crawl Space Floors in Existing Homes

Guide

Guide describing how to upgrade a crawlspace floor in an existing home by adding insulation.

Below Deck Spray Foam Insulation for Existing Roofs

Guide

Guide describing how to add spray foam insulation to the underside of the existing roof deck as part of the conversion of a vented attic to an unvented, insulated attic.

Form an insulation dam of sheet metal around a flue pipe in the attic after air sealing around the pipe with sheet metal and fire-rated caulk or canned foam

Image