BASC Search

Taped Insulating Sheathing Drainage Planes

Guide describing techniques for installing insulating sheathing as a continuous drainage plane on walls.

Certified Insulated Siding: Quality, Comfort and Energy Performance

Author(s)

Dobson,

Brignati

Organization(s)

Vinyl Siding Institute,

Newport Ventures

This presentation will help you define insulated siding, understand R-value testing of insulated siding, describe proper installation of insulated siding, comply with energy codes and understand building energy performance program and software recognition.

Upper wall insulation installation with butyl z-flashing

Publication Date

Mon, 09/01/2014 - 12:00

This exterior insulated slab-on-grade monolithic grade beam foundation is protected from pests by termite shield at the sill plate, borate-treated framing, flashing at end of wall insulation, brick veneer over slab-edge insulation, and rock ground cover.

Publication Date

Mon, 03/01/2021 - 12:00

Measure Guideline: Guidance on Taped Insulating Sheathing Drainage Planes

Author(s)

Grin Aaron,

Lstiburek Joseph W

Organization(s)

Building Science Corporation,

BSC

Publication Date

September, 2014

Measure Guideline research report providing simple, long term, and durable solutions when using tapes and flashing membranes in conjunction with the exterior face of rigid polymeric foam sheathing to create the drainage plane of a wall system.

Expanded polystyrene insulation is installed with joints taped and lath attached in preparation for the application of stucco

Clean taping areas and install 3" tape on vertical joint of upper insulation overlapping the horizontal joint

Publication Date

Mon, 09/01/2014 - 12:00

Tape the joint between the top insulation sheet and the Z-flashing with 2" wide tape to improve air tightness

Publication Date

Mon, 09/01/2014 - 12:00

Right – The flashing is properly installed to create a complete drainage system with continuous rigid insulation sheathing/siding

Publication Date

Tue, 02/01/2011 - 12:00

This farmhouse was retrofit by removing the existing siding and adding taped insulated sheathing and battens before installing new siding

Step 1. Apply roof underlayment over roof deck and up the sidewall over the rigid foam insulation

Reference

40% Whole-House Energy Savings in the Marine Climate, Volume 11

Author(s)

Baechler Michael C,

Gilbride Theresa L,

Hefty Marye G,

Cole Pam C,

Williamson Jennifer,

Love Pat M

Organization(s)

Pacific Northwest National Laboratory,

PNNL,

Oak Ridge National Laboratory,

ORNL,

U.S. Department of Energy,

DOE

Report providing builders in marine climates with guidance for building homes that have whole-house energy savings of 40% over the Building America benchmark with no added overall costs for consumers.

Publication Date

Wed, 09/01/2010 - 12:00

Step 5. Apply self-adhesive flashing over top edge of the wall flashing, diverter, and rigid foam insulation

Reference

40% Whole-House Energy Savings in the Marine Climate, Volume 11

Author(s)

Baechler Michael C,

Gilbride Theresa L,

Hefty Marye G,

Cole Pam C,

Williamson Jennifer,

Love Pat M

Organization(s)

Pacific Northwest National Laboratory,

PNNL,

Oak Ridge National Laboratory,

ORNL,

U.S. Department of Energy,

DOE

Report providing builders in marine climates with guidance for building homes that have whole-house energy savings of 40% over the Building America benchmark with no added overall costs for consumers.

Publication Date

Wed, 09/01/2010 - 12:00

This house design in the Hot-Humid climate uses a slab foundation, masonry walls, and an Exterior Insulation Finish System (EIFS) cladding.

Publication Date

Thu, 09/01/2011 - 12:00

Rigid foam insulation can serve as the drainage plane when all seams are taped. Furring strips provide an air gap behind the cladding.

Publication Date

Sun, 04/01/2012 - 12:00

Standard Practice for the Installation of Mounting Flange Windows into Walls Utilizing Foam Plastic Insulating Sheathing (FPIS) with a Separate Water-Resistive Barrier (WRB), FMA/AAMA/WDMA 500-16

Author(s)

Fenestration Manufacturers Association,

American Architectural Manufacturers Association,

Window & Door Manufacturers Association

Organization(s)

FMA,

AAMA,

WDMA

Publication Date

April, 2016

Guide describing the installation of windows in walls that have foam plastic insulating; guide provides several methods for attaching, supporting, and flashing windows in walls with rigid foam sheathing. (Note: The link only goes to the table of contents for the guide, the full guide can be...

This basement is insulated on the exterior with rigid foam over dampproofing, with granular backfill and footing drains to facilitate drainage away from the foundation, a termite shield to protect from pests, and cellular PVC to protect the rigid foam.

Publication Date

Mon, 03/01/2021 - 12:00

Right - Permeable rigid mineral wool insulation and appropriate water-management flashing details are integrated with new rigid foam siding to keep water away from the sill beam above the foundation wall

Vinyl Siding with Integrated Rigid Foam for Existing Walls

Guide describing the design and installation considerations for recladding of above grade walls using insulated vinyl siding.

Proper flashing around windows is especially important when the rigid foam serves as the drainage plane in the wall

Publication Date

Mon, 10/01/2007 - 12:00

Water Managed Existing Sill Beams and Sill Plates

Guide describing how to insulate the sill beam or sill plate on the exterior side in a way that allows drying to the exterior, as part of an exterior wall upgrade.

Moisture Management in Residential Construction Series - Building Enclosure: Exterior Wall Overview

Publication Date

January, 2011

Author(s)

Home Innovation Research Labs

Organization(s)

Home Innovation Research Labs

Video from Home Innovation Research Labs giving an overview of moisture problems common to exterior walls and how to mitigate these problems with proper framing, flashing, sheathing, cladding, and insulation.

Mastic Home Exteriors Installation Guide

Author(s)

Ply Gem Siding Group

Organization(s)

Ply Gem Siding Group

Publication Date

April, 2015

Siding installation guide for Ply Gem Siding Group products.

Flashing of Wall Penetrations in Existing Homes

Guide describing how to install flashing that is integrated with air and water control layers around piping, vents, and other wall penetrations as part of an exterior wall retrofit.

Install minimum 6" wide self-adhered butyl Z-flashing

Publication Date

Mon, 09/01/2014 - 12:00

This exterior wall retrofit permits drying to the exterior of a sill plate installed on an untreated irregular foundation wall

Publication Date

Mon, 07/01/2013 - 12:00

This exterior wall retrofit permits drying to the exterior of a sill plate installed on an untreated flat foundation wall

Publication Date

Mon, 07/01/2013 - 12:00

Moisture Control for Residential Buildings

Author(s)

Lstiburek Joseph W

Organization(s)

Building Science Corporation,

BSC,

U.S. Department of Energy,

DOE

Publication Date

September, 2020

Report providing extensive guidance on controlling moisture in building envelopes through proper selection and installation on air, water, thermal, and vapor barriers.

Taped Insulating Sheathing Drainage Planes

Certified Insulated Siding: Quality, Comfort and Energy Performance

Upper wall insulation installation with butyl z-flashing

This exterior insulated slab-on-grade monolithic grade beam foundation is protected from pests by termite shield at the sill plate, borate-treated framing, flashing at end of wall insulation, brick veneer over slab-edge insulation, and rock ground cover.

Measure Guideline: Guidance on Taped Insulating Sheathing Drainage Planes

Expanded polystyrene insulation is installed with joints taped and lath attached in preparation for the application of stucco

Clean taping areas and install 3" tape on vertical joint of upper insulation overlapping the horizontal joint

Tape the joint between the top insulation sheet and the Z-flashing with 2" wide tape to improve air tightness

Right – The flashing is properly installed to create a complete drainage system with continuous rigid insulation sheathing/siding

This farmhouse was retrofit by removing the existing siding and adding taped insulated sheathing and battens before installing new siding

Step 1. Apply roof underlayment over roof deck and up the sidewall over the rigid foam insulation

Step 5. Apply self-adhesive flashing over top edge of the wall flashing, diverter, and rigid foam insulation

This house design in the Hot-Humid climate uses a slab foundation, masonry walls, and an Exterior Insulation Finish System (EIFS) cladding.

Rigid foam insulation can serve as the drainage plane when all seams are taped. Furring strips provide an air gap behind the cladding.

Standard Practice for the Installation of Mounting Flange Windows into Walls Utilizing Foam Plastic Insulating Sheathing (FPIS) with a Separate Water-Resistive Barrier (WRB), FMA/AAMA/WDMA 500-16

This basement is insulated on the exterior with rigid foam over dampproofing, with granular backfill and footing drains to facilitate drainage away from the foundation, a termite shield to protect from pests, and cellular PVC to protect the rigid foam.

Right - Permeable rigid mineral wool insulation and appropriate water-management flashing details are integrated with new rigid foam siding to keep water away from the sill beam above the foundation wall

Vinyl Siding with Integrated Rigid Foam for Existing Walls

Proper flashing around windows is especially important when the rigid foam serves as the drainage plane in the wall

Water Managed Existing Sill Beams and Sill Plates

Moisture Management in Residential Construction Series - Building Enclosure: Exterior Wall Overview

Mastic Home Exteriors Installation Guide

Flashing of Wall Penetrations in Existing Homes

Install minimum 6" wide self-adhered butyl Z-flashing

This exterior wall retrofit permits drying to the exterior of a sill plate installed on an untreated irregular foundation wall

This exterior wall retrofit permits drying to the exterior of a sill plate installed on an untreated flat foundation wall

Moisture Control for Residential Buildings

Step and Kick-Out Flashing at Roof-Wall Intersections

Windows and Doors are Fully Flashed

Flashing at Bottom of Exterior Walls

Flashing of Roof-Wall Intersections in Existing Homes