Carpet Not Installed in Wet Areas


Do not install carpet in areas that are likely to get wet, such as bathrooms, kitchens, entry ways, or laundry rooms.
Do not install carpet in areas that are likely to get wet, such as bathrooms, kitchens, entry ways, or laundry rooms.

Avoid installing carpet in areas within the home that are likely to become wet.

Install only water-resistant hard-surface flooring in kitchens, bathrooms, entryways, laundry areas, and utility rooms (Indoor airPLUS). 

See the Compliance Tab for related codes and standards requirements, and criteria to meet national programs such as DOE’s Zero Energy Ready Home program, ENERGY STAR Certified Homes, and Indoor airPLUS.


Water splashing or spraying out of sinks and tubs; rain and snowed tracked in on wet shoes; and water vapor in the air from cooking, laundry, and bathing – all contribute to wet floor surfaces. When the floor surface is covered with carpet, it can take longer for the moisture to evaporate, leading to mold and mildew problems. Carpet can also hide water leaks and spills that may result in warping, swelling, and rotting of the subfloor. To minimize the opportunity for mold growth and structural damage, carpet should not be installed in rooms where floors are likely to get wet such as bathrooms, kitchens, entry ways, laundry rooms, or utility rooms. Instead water-resistant hard-surface flooring should be installed in these areas.

The design and construction of bathrooms and other wet areas of the home should be part of a comprehensive water management strategy that includes the following:

See the ENERGY STAR Water Management System Builder Checklist for additional guides to help you design and construct a home with reduced risk of water damage.  

Mold on the Wall, Baseboard, and Carpet

Figure 1. Wall-to-wall carpet installed in a bathroom will likely become wet, encouraging mold growth like the mold visible on this wall, baseboard, and carpet. Reference

Several hard-surface flooring products are appropriate for areas of the home that are likely to get wet – ceramic tile, stone, and vinyl flooring are all good choices.

The following flooring materials are hard surface but are not recommended for areas prone to water spills. 

  • Hardwood flooring. Although usually sealed and water proofed, hardwood flooring is not generally rated for excessive and repeated exposure to water.
  • Laminate flooring. Laminate flooring is made from either melamine resin or linseed oil and wood chips. Although laminate flooring can tolerate some exposure to water, excessive saturation, spills, or standing water can cause the planks to swell and buckle. 
  • Bamboo, cork, and alternative flooring options. Other types of modern sustainable flooring options such as bamboo and cork are not appropriate for wet areas as they will warp, swell, and wear poorly when exposed to the amount of water expected in a bathroom or kitchen.

Due to the amount of water that can be introduced into the home from showers, tubs, and toilets, consider designing and building the bathroom, the laundry room, and/or the kitchen as a true “wet room” as described below (BSC 2009). A designed wet room is built to contain and remove excessive water, keeping it from entering other parts of the house.

How to Select Water-Compatible Flooring

  1. Select appropriate flooring materials for wet areas including bathrooms, kitchens, entryways, laundry rooms, and utility rooms (EPA 2012):
  • Ceramic tile. Ceramic tile is a clay-based material that is kiln dried and installed in mortar or thin set over a cement backer-board. Once installed, the tiles are treated with a water-resistant finish that protects the floor and subfloor. Relative to other flooring types, ceramic tile is moderately priced.
  • Stone. Stone is a natural product that is installed like ceramic tile over a cement backer-board in thin set. Natural stone can be marble, granite, travertine, or terrazzo and must also be treated with a waterproof coating. Stone is the most expensive flooring option.
  • Vinyl flooring. Vinyl flooring comes in rolls, planks, and tiles, and is composed of polyvinyl chloride (PVC) resin along with additives such as plasticizers, stabilizers, pigments, and fillers (EPA 2012). Vinyl flooring is relatively inexpensive compared to ceramic tile and stone flooring. When properly installed, vinyl flooring provides a waterproof barrier between the bathroom and subfloor. Sheet vinyl flooring that comes in rolls is typically installed using an adhesive that is painted or sprayed directly on the subfloor, although heavier varieites may be installed as non-glued or "floating floor" products. Vinyl planks and tiles may be designed with a tongue-and-groove connecting system that also produces a floating (non-glued) surface. If choosing click-together vinyl plank or tiles, look for products that are reported to have water-tight seams. Vinyl planks and tiles are also available with a self-adhesive peel-and-stick backing material; these products may not hold up as well to repeated saturations.
  • Sealed concrete flooring. When sealed, concrete provides a non-pervious, water-resistant surface that is ideal for wet areas. Concrete’s thermal mass lends itself to radiant floor heating. Clear chemical sealants must be reapplied every 1 to 2 years. The sealant can contain particles to provide traction on wet floors.

Select Flooring Appropriate for Wet Area

Figure 2. Select Flooring Appropriate for Wet Area. The toilet, sink, bath, and shower are all significant sources of water, and flooring options need to be selected that do not absorb water and are not damaged by water.  Reference

How to Design a “Wet Room” (BSC 2009)

  1. Install a water-resistant flooring material (as listed above and according to manufacturer’s specifications) that extends wall to wall and is continuous under fixtures and cabinets.
  2. Eliminate unnecessary penetrations through the floor. Caulk and seal carefully around any necessary plumbing pipe penetrations.
  3. Install water-resistant baseboard material that is sealed to the floor or install floor material that is turned up at the walls and sealed at the corners.
  4. Install a floor drain that is properly attached to the home’s sewer system.
  5. Install a raised sill at doorways to contain any excess water that may flow toward the rest of the home.
  6. Use non-paper-faced drywall and install the drywall at least ½-inch above the finished floor to reduce the chance of wall materials coming into contact with water and to facilitate drying of wall cavities.

Ensuring Success

Avoid installing carpet in areas that routinely get wet or have an increased likelihood of getting wet such as bathrooms, kitchens, entryways, laundry areas, and utility rooms.

When designing and building the home, employ a comprehensive water management strategy.


No climate-specific information applies.


Right and Wrong Images


None Available


None Available

CAD Images

None Available


The Compliance tab contains both program and code information. Code language is excerpted and summarized below. For exact code language, refer to the applicable code, which may require purchase from the publisher. While we continually update our database, links may have changed since posting. Please contact our webmaster if you find broken links.

ENERGY STAR Certified Homes

ENERGY STAR Certified Homes (Version 3/3.1, Revision 08), Water Management System Builder Requirements

4. Water-Managed Building Materials: 

4.1 Wall-to-wall carpet not installed within 2.5 ft. of toilets, tubs, and showers.

Builders Responsibilities:  It is the exclusive responsibility of builders to ensure that each certified home is constructed to meet these requirements. While builders are not required to maintain documentation demonstrating compliance for each individual certified home, builders are required to develop a process to ensure compliance for each certified home (e.g., incorporate these requirements into the Scope of Work for relevant sub-contractors, require the site supervisor to inspect each home for these requirements, and / or sub contract the verification of these requirements to a Rater). In the event that the EPA determines that a certified home was constructed without meeting these requirements, the home may be decertified. 

ENERGY STAR Revision 08 requirements are required for homes permitted starting 07/01/2016.

DOE Zero Energy Ready Home

The DOE Zero Energy Ready Home program requires that builders comply with EPA Indoor airPLUS. The Indoor airPLUS checklist (Item 1.11) requires that builders install only water-resistant hard-surface flooring in kitchens, bathrooms, entryways, laundry areas, and utility rooms.

More Info.

Access to some references may require purchase from the publisher. While we continually update our database, links may have changed since posting. Please contact our webmaster if you find broken links.

Case Studies

  1. Author(s): BSC
    Organization(s): BSC
    Publication Date: July, 2010

    Case study describing a building project in the hot-humid climate zone.

References and Resources*

  1. Author(s): DOE
    Organization(s): DOE
    Publication Date: April, 2017

    Standard requirements for DOE's Zero Energy Ready Home national program certification.

  2. Author(s): EPA
    Organization(s): EPA
    Publication Date: December, 2015

    Document outlining the program requirements for ENERGY STAR Certified Homes, Version 3 (Rev. 08).

  3. Author(s): BSC
    Organization(s): BSC
    Publication Date: May, 2009
    Brochure about indoor water management.
  4. Author(s): EPA
    Organization(s): EPA
    Publication Date: September, 2012
    Presentation, and online course, that provides an introduction to mold and mold remediation for environmental and public health professionals.
  5. Author(s): EPA
    Organization(s): EPA
    Publication Date: February, 2011
    Guide describing details that serve as a visual reference for each of the line items in the Water Management System Builder Checklist.

Contributors to this Guide

The following authors and organizations contributed to the content in this Guide.

Last Updated: 06/08/2016

Mobile Field Kit

The Building America Field Kit allows you to save items to your profile for review or use on-site.