Skip to main content

Supply Integrated with HVAC

Installed correctly, a whole-house fresh air system helps ensure a healthier indoor environment.

PDF Version:
English
Spanish

Checklist

This U.S. Department of Energy checklist includes important specifications that can contribute to a complete and quality installation. All work shall comply with these specifications, all relevant codes and standards, and all manufacturer installation instructions. The contractor shall check each box on the checklist below and sign and date at the bottom to certify the work is completed.

Preparation
▢
For continuous operation, the target ventilation rate for the home shall be based on house size as follows: 50 cfm for up to 1,500 ft2, 70 cfm for 1,501 to 2,500 ft2, and 100 cfm over 2,500 ft2. For intermittent operation, the average air flow shall meet the minimum target ventilation rate specified above (e.g., if the controller operates the air handler fan for a minimum of 20 minutes each hour, then three times the target ventilation air flow is needed).
▢
An outdoor air intake location shall be selected that is close to the return plenum of the central air handler and will provide a short, straight, unobstructed path from the air intake to the return plenum to provide unrestricted airflow. The equivalent length of the duct run should be as short as possible. “Equivalent length” shall be calculated in accordance with ANSI/ACCA Manual D Residential Duct Systems.
▢
The air intake should open to the outdoors, not to an attic, basement, garage, or crawlspace. The location should be away from garages or parking areas; at least 10 feet from any exhaust termination; and accessible from the ground for cleaning and maintenance, but well above the snow level. The air intake should be equipped with an air filter that is MERV 11 or better. The pressure drop across the filter shall be measured and verified to match equipment capabilities.
▢
If the HVAC air handler has a PSC (permanent split capacitor) motor, the PSC motor shall be replaced with a variable-speed motor (ECM or BPM).
▢
A controller shall be selected that is compatible with the existing air handler and control system.
Installation
▢
Outdoor air shall be filtered with a MERV 11 filter or higher, and the pressure drop across the filter shall match equipment capabilities. The filter shall be installed to be easily accessible by occupants.
▢
The exhaust duct outlet vent shall be located on the exterior of the home where it does not direct air flow onto a walkway and where it is situated at least 10 feet from any air inlet.
▢
Outdoor air intakes shall be equipped with screens to keep out insects and debris, integrated with siding and flashed properly to prevent water intrusion, and caulked where the edges of the duct meet the exterior walls or ceilings to limit the infiltration of exterior air into the home.
▢
All duct seams and connections shall be sealed with mastic or UL 181 tape.
▢
Ducts installed outside of the thermal envelope shall be insulated to a minimum of R-8.
Commissioning
▢
The ventilation rate shall be measured using a flow hood, flow grid, or anemometer, in accordance with test procedures listed in ANSI/RESNET/ICC 380-2016, to ensure that the fan is providing the minimum ventilation rate specified above.
▢
All operation and maintenance procedures shall be reviewed with the homeowner (e.g., how and when to change filter).

Supply Integrated with HVAC Background

Supply Integrated with HVAC

Contaminants in homes can trigger asthma and allergy attacks as well as other health problems. Whole-house fresh air systems dilute these contaminants. Supply fresh air systems provide effective ventilation by bringing fresh air into the home through dedicated fresh air ducts equipped with filters rather than through unknown sources like cracks in the building envelope. Electronic controls operate the air handler fan of the central heating and cooling system to periodically draw a set amount of fresh air into the home throughout the day, even when the thermostat is not calling for heating and cooling. The exhaust of stale indoor air relies on natural exfiltration.

Tips to Sell Quality Installed Home Improvements

Home Improvement Expert is a valuable tool for organizations committed to quality installed work. The following tips help optimize the value of this tool when selling home improvements:

Trust Matters: Inform homeowners how your work conforms to this world-class expert guidance. Recommend they visit the DOE website as evidence these are indeed official best practices.

Knowledge Matters: Take advantage of the Building America Solution Center as a resource for becoming an expert on these projects.

Clarity Matters: Tell prospective clients to contrast your expert-recommended best practices with other contractors.

Value Matters: Advise prospective clients to insist other bids also include these checklists to ensure equivalent quality work.

Message Matters: Showcase on your website and marketing materials that your company uses the highest quality best practices specified on HIE Checklists.

Experiences Matter: Provide visual evidence contrasting the difference between poor and high quality work such as infrared images; pre- and post-energy bills; short and long warranties; and simple charts and graphics depicting performance advantages.

BASC Guides

High-MERV Filters

This guide describes the uses, selection process, and specification of high-MERV filters.
Back to Checklists