Showing results 501 - 550 of 1073
Image
Image
Right - External outlet wall penetration is flashed with tape that is properly layered with house wrap.
Image
Right - Flaps are cut into house wrap installed over an HRV duct then taped out of the way to install flashing; 8 of 14.
Image
Image
Right - Foil-faced polyisocyanurate rigid foam is attached to the existing exterior wall with vertical wood furring strips
Image
Right - Furring strips create an air gap to allow penetrating moisture to drain instead of wicking into walls; they also provide a nailing surface for siding.
Image
Right - Furring strips were installed with blocking to allow adequate room for 4 inches of mineral wool.
Image
RIght - Furring strips, house wrap, and siding are installed in the field after assembling panelized walls.
Image
Right - House wrap is overlapped “shingle” style to direct moisture down and away from the house; seams will be taped so house wrap serves as both an air and weather barrier.
Image
Right - Installation steps for the L-bent strap method of bracing a gable end wall
Image
Right - Ladder blocking allows insulation to be installed in exterior walls at interior-exterior wall intersections.
Image
Right - Mastic is being installed to air seal the wood-to-wood joints in this wall.
Image
Right - Metal connectors provide uplift resistance at the rim joist between floors in new construction for a continuous load path.
Image
Right - Metal connectors provide uplift resistance at the stud-to-bottom plate connection in new construction for a continuous load path.
Image
Right - Mineral Wool insulation is installed on the exterior of wall with furring strips.
Image
Right - New flashing has been installed to complete the air and water control layers at the window openings of this wall retrofit that includes insulating the wall cavities with spray foam
Image
Right - Panelized walls came to site with house wrap and furring strips pre-installed; seams will be overlapped and taped on site.
Image
Right - Panelized walls came to site with house wrap pre-installed and ready to unfurl to cover foundation-to-sheathing seam.
Image
Right - Permeable rigid mineral wool insulation and appropriate water-management flashing details are integrated with new rigid foam siding to keep water away from the sill beam above the foundation wall
Image
Right - Plywoood sheathing is taped at the seams to create a continuous air barrier that prevents air infiltration through critical junctures in the wall, such as at corners and between floors.
Image
Right - Precast concrete basement walls come to the site with integrated rigid foam insulation and steel-faced concrete studs.
Image
Image
Right - Seams in coated sheathing and joints around window are properly sealed and flashed with tape and all nail holes are covered with paint-on sealant.
Image
Right - Spray foam fills the walls and rim joists to air seal and insulate while caulk seals the framing joints.
Image
Right - Tape flashing keeps moisture out around and below the window; extra tape reinforces the corners to prevent tearing of the house wrap and to keep water out of this critical juncture.
Image
Right - The poured concrete basement walls are insulated along the inside with 2.5 inches of extruded polystyrene insulation.
Image
Right - The slab-on-grade foundation is insulated with two layers (R-20) of XPS foam under the-slab and R-10 on the exterior of the stem walls.
Image
Right - The wall framing is connected to roof framing with metal ties for hurricane-resistant construction.
Image
Right - These attic knee walls are insulated with rigid foam and sealed with spray foam to form a continuous air barrier at the gable end of this cathedral ceiling.
Image
Right - These raised heel roof trusses provide 16 inches of space over the outer walls for full insulation coverage at the attic perimeter.
Image
Right - This concrete basement wall has exterior rigid insulation and comprehensive moisture management details.
Image
Right - This foil-faced polyisocyanurate rigid foam is installed on an existing exterior wall and the seams are taped so the rigid foam can serve as a water control layer
Image
Right - This high-thermal-mass home uses masonry construction to naturally regulate temperatures inside the house
Image
Image
Right - Walls and ceilings shared by the garage and living space must be air sealed and insulated.
Image
Image
Right - XPS foam insulation is attached to the existing exterior wall with wood furring strips that serve as a nail base for the siding and are installed vertically to allow for drainage and drying behind the siding
Image
Right – Deep overhangs, pergolas, and covered entryways minimize heat gain in this commercial building in the hot-dry climate.
Image
Image
Image
Right – A bead of sealant will form an airtight gasket between the top plate and drywall.
Image
Image
Right – A gap separates the two wall layers in this double-stud wall assembly allowing room for insulation to stop thermal bridging between the inner and outer wall
Image
Right – Air barrier and penetrations sealed between porch attic and conditioned space
Image
Image
Image
Right – Air barrier installed under staircase (picture taken from house looking into attached garage)
Image
Image
Image
