Showing results 1 - 100 of 117
Image
A plastic fiber drainage mat rainscreen provides uniform support for the siding and allows moisture to flow horizontally and diagonally in addition to vertically.
Image
A raised wood pier foundation can raise the subfloor above the design flood elevation.
Image
A single-story house floor plan showing braced wall line locations at A through E and 1 through 5
Image
Add metal connectors to strengthen framing connections in an existing wall from inside the home by removing drywall.
Image
Image
Image
Image
Image
Building America worked with Mercedes Homes in east Florida to design homes using cast-in-place concrete walls capable of withstanding wind-blown debris impacts of up to 200 mph (Source: Mercedes Homes).
Image
Buildings damaged by a hurricane storm surge: upper homes on gulf shoreline were hit by large waves above the lowest floor, lower left home on bay and right school 1.3 miles from gulf shoreline were hit by surge and small waves.
Image
Image
Connecting hardware helps tie the roof to the walls to ensure a continuous load path to improve a building’s resistance to high winds, floods, and earthquakes.
Image
Connecting hardware helps tie the walls to the top plates and rim joists to ensure a continuous load path to improve a building’s resistance to high winds, floods, and earthquakes.
Image
Image
Correct seismic retrofit hardware for securing the sill plate to foundation wall
Image
Image
Image
Durability concerns on a house continuously sheathed with a proprietary fiber structural panel used as bracing. Photo 1 of 2.
Image
Durability concerns on a house continuously sheathed with a proprietary fiber structural panel used as bracing. Photo 2 of 2.
Image
End conditions for braced wall lines with continuous sheathing, Figure R602.10.7 in the IRC
Image
Example A of a gable truss and gable end wall bracing for a home in a hurricane region
Image
Example B of a gable truss and gable end wall bracing for a home in a hurricane region
Image
Example of masonry construction. Wall separated from building envelope due to inadequate vertical wall reinforcing in connection to horizontal tie-beam.
Image
Failure of a freestanding concrete masonry end wall due to discontinuous tie-beam when exposed to hurricane force winds.
Image
Image
Firewall separation. Results from building corners being discontinuous with tie-beams.
Image
Image
Image
Good water management practices like sloping grade away from house, and installing gutters, perimeter drain pipe, a capillary break, and free-draining soils or drainage mat protect the foundation from water saturation.
Image
House wrap is sealed at all seams and overlaps flashing to serve as a continuous drainage plane over the exterior walls.
Image
Hurricane force winds that breach external windows and doors can then cause failure of the entire building due to internal pressures on walls and roof.
Image
Hurricane straps, hold-down connectors, and bolts help to transfer loads from the building’s walls to its foundation, increasing resistance to vertical and horizontal pressures acting on the building from wind, waves, or ground movement.
Image
Image
Improper continuous load path design lacking bracing results in the failure of gable end walls under high wind conditions.
Image
Image
In areas prone to high winds and hurricanes, double vertical “jack trim” and horizontal “header” and “sill” studs are recommended on all sides of window and door openings.
Image
In high wind areas, provide lateral support to masonry end walls to resist high winds.
Image
In high-wind regions, special hardware is used for most framing connections; toe-nailing is not acceptable.
Image
Image
Install all layers of the drainage plane to overlap, not underlap, to direct bulk water down and out of the wall.
Image
Install furring strips over house wrap to provide a rainscreen behind wood siding.
Image
Image
Image
Image
Image
Key connection points for a continuous load path for earthquake and high wind disaster resistance
Image
Image
Lower-story wall anchorage to masonry (or concrete) base. Straps properly nailed at wall studs.
Image
Image
Image
Moisture-resistant plastic and fiber cement exterior trim and cladding are indistinguishable from wood building elements.
Image
Image
Image
Image
Image
Properly reinforce masonry walls in coastal locations to resist high winds and waves.
Image
Image
Recommended flood resistant wall construction for concrete block walls with stucco or brick veneer.
Image
Image
Image
Redundant moisture barriers including siding, house wrap, and coated sheathing can help protect walls from excess moisture, while vapor retarders prevent vapor from entering the wall from the house, for example from a bathroom or kitchen.
Image
Right – The ties are bent at a 90 degree angle at the nail head and embedded into the mortar joint at least 1.5 inches.
Image
Right - A continuous load path connects the roof and wall framing to the foundation.
Image
Right - Anchorage to increase the wind uplift resistance of outlookers forming the overhang at a gable end truss wall.
Image
Right - Braced wall line spacing is correctly calculated for determining wall bracing in accordance with the IRC.
Image
Right - Engineered portal frames are used for wall bracing to resist wind and earthquake loads.
Image
Image
Image
Right – Examples of wall stud to sill plate and foundation and wall rod connectors and brackets.
Image
Right – Examples of wall stud to top plate and stud to rim joist framing connectors and brackets.
Image
Right – Furring strips provide a drainage gap between the rigid foam and the siding.
Image
Image
Image
Image
Right – The building felt is installed on all exterior walls and provides a complete drainage system
Image
Right – The rigid insulation covers all exterior walls and all seams are taped to provide a complete drainage system
Image
Right – The water-resistant barrier covers the entire house and the seams are taped to provide a complete drainage system
Image
Right – This low-slope roof and parapet assembly has continuity of both the air and water barriers
Image
Rigid foam insulation can serve as the drainage plane when all seams are taped. Furring strips provide an air gap behind the cladding.
Image
Image
Image
Shear Strength Comparison Between a Foundation Stud Anchor (on left) and a Shear Transfer Angle (on right)
Image
Step 1. Remove the existing wall cladding to prepare to retrofit an exterior wall.
Image
Step 2. Install a continuous air and water control layer over the existing wall sheathing.
Image
Step 3. Apply urethane sealant around the duct or pipe in the retrofitted exterior wall.
Image
Step 4. Install insulating sheathing and vertical furring strips on the retrofitted exterior wall; seal around pipe or duct with urethane sealant.
Image
Step 5. Install sheathing tape flashing over the duct or pipe and wood blocking on either side for later attachment of trim.
Image
Step 6. Install vent hood trim block, metal cap flashing; seal top edge of flashing with sheathing tape.
Image
Image
Step 8. Attach the new cladding to the furring strips over the rigid foam for the exterior wall retrofit.
Image
The components of a framed wall include from inside to out: gypsum, wood studs, OSB or plywood sheathing, and siding.
Image
Image
Image
Image
The sheathing has rotted because there was not a sufficient drainage gap behind the stucco cladding
Image
Upper-floor tie to lower floor for two-story building. Floor tie anchor and nailed wall sheathing.
Image
Image
With fiber cement siding, face nail rather than blind nail where the design wind speed is ≥100 mph.
Image
With fiber cement siding, place blind nails 3/4 to 1 inch from top edge and > 3/8 inch in from butt ends.
Image
