Showing results 1 - 50 of 63
Image
A piece of siding is used as sill extension and to provide slope in the opening for the window, which is deeper because exterior rigid foam has been added
Image
Image
Apply self-adhesive flashing over top edge of the wall flashing, diverter, and housewrap
Image
Clean taping areas and install 3" tape on vertical joint of upper insulation overlapping the horizontal joint
Image
Continuous L-metal flashing integrated with underlayment at roof-wall intersections
Image
Image
Drip flashing at the door head and drip flashing with hook at the head help to keep out wind-driven rain.
Image
Duct/pipe penetration with metal cap flashing and wood blocking for trim attachment
Image
Existing wall-to-lower roof transition retrofitted with a new strip of fully adhered air control transition membrane, new step flashing, new roof underlayment, and new cladding
Image
Existing wall-to-lower roof transition with a new strip of fully adhered air control transition membrane, new step flashing, new roof underlayment, and new cladding – view from eave
Image
Existing wall-to-lower roof with attic transition with a new strip of fully adhered air control transition membrane, new step flashing, new roof underlayment, and new cladding – view from eave
Image
Image
Heavy metal flashing protects the deck timbers and separates them from the wall at the wall-deck connection which is vulnerable to both ember entrapment and water damage.
Image
Improper flashing can allow rain water into walls, causing significant damage
Image
Image
Image
Install shingle starter strip then kick-out diverter; attach to roof deck but not sidewall
Image
Image
Image
Integrate pre-formed vent pipe flashing, shingle-fashion, with roofing underlayment and shingles
Image
Kickout diverter flashing keeps bulk water from the roof from overflowing the gutter and continuously wetting the siding material.
Image
Place first shingle and next section of sidewall flashing over upper edge of diverter
Image
Plan view of duct or pipe penetration through exterior wall showing flashing and air sealing details
Image
Plan view of electric box installation in exterior wall showing flashing and air sealing details
Image
Right - Counterflashing tops a layer of step flashing which comes down above the asphalt shingle and a layer of L-shaped base flashing which comes down and extends below the shingle; the base flashing is adhered to the roof underlayment with mastic, shown
Image
Right - Pieces of metal flashing are installed under each tile course along the valley centerline to prevent debris accumulation between and below concrete roof tiles.
Image
Right - Step flashing along a chimney is integrated in a layered manner with asphalt shingle roofing and topped with counterflashing that is embedded into brick mortar joint above
Image
Right - The duct shows redundant sealing including the caulk, tape, and flashing
Image
Right - The pipe penetration is properly flashed and furring strips are installed on each side in preparation for installing cladding
Image
Image
Right - The water and air control layers are properly integrated around the hose bib
Image
Right - This duct penetration is properly flashed and integrated with the taped, foil-faced foam sheathing layer, which serves as the air and water barrier
Image
Right – A chimney cricket is installed and flashed to direct rainwater around the chimney
Image
Right – All penetrations through the roof decking are sealed with paint-on flashing.
Image
Right – Deck flashing protects the deck-to-wall connection from water and burning embers.
Image
Right – Flashing is installed around chimney, skylight, vents, dormers, in valleys and at eaves
Image
Image
Right – Metal flashing is installed between the deck boards and house wall with the top of the flashing extending up behind the siding and the bottom of the flashing extending out and down over the ledger board
Image
Image
Right – The water-resistant barrier is layered over the step flashing to provide a complete drainage system
Image
Right – Two-thirds of acrylic tape is offset above the joint and over and above the fasteners
Image
Right – two-thirds of the blue butyl flashing tape is above the sheathing seam; the top edge of the butyl flashing tape is covered with clear sheathing tape that is also offset so two-thirds is above the top edge of the butyl flashing.
Image
Rigid foam insulation can serve as the drainage plane when all seams are taped. Furring strips provide an air gap behind the cladding.
Image
Image
Image
Section view of duct or pipe penetration through exterior wall showing flashing and air sealing details
Image
Section view of electric box installation in exterior wall showing flashing and air sealing details
Image
Image
Step 1. Apply roof underlayment over roof deck and up the sidewall over the rigid foam insulation
Image
Step 2. Install shingle starter strip then kick-out diverter as first piece of step flashing.