Library

Technical report describing the Re-Side Right initiative by the New Jersey Institute of Technology's Building America research team that proposes enhancing home efficiency during the re-siding process by incorporating an insulating layer that acts as both an air barrier and water resistive barrier...

Research study about two test homes that are examined with the goal of providing case studies that could be applied to other similar New England homes.

Report covering the reconstruction of flood damaged homes.

Webpage explaining how to mitigate heat loss through roofs for ice dam prevention.

Report researching cost- effective solution packages for significant energy efficiency and indoor air quality improvements masonry multifamily urban buildings.

Table in the IRC describing bracing requirements for specified wind speeds and building story locations.

Technical bulletin describing National Flood Insurance Program (NFIP) requirements for flood openings in foundation walls and walls of enclosures below elevated buildings.

Website describing the U.S. Department of Energy's residential buildings program.

Report describing a study using parametric computer simulations of 112 single-family and 63 multi-family residential building prototypes to quantify the contributions of building components such as roofs, walls, windows, infiltration, outside air, lighting, equipment, and people to the aggregate...

Website providing resources for seismic retrofits for builders and homeowners as well as city permit requirements from the City of Portland OR.

Report providing architects, designers, and homeowners with information to make house plans useful for constructing a more wind resilient structure.

Report describing the testing of various siding materials for their ability to resist bullets from small firearms.

Presentation describing RESNET grading criteria for insulation installation.

Report describing how modification of model specifications to include guidance on energy efficiency measures can create a greater level of consistency in executing energy efficiency retrofit measures across the multiple regions where a developer may work.

Fact sheet describing flashing of roof penetrations to make a home more resistant to high winds, hurricanes, and rainwater intrusion.

Report describing the costs, benefits, and challenges of attic insulation retrofits in HUD-code manufactured homes.

Guide on retrofitting insulation in cavities.

Report about a deep energy retrofit Cool Energy House.

Report describing how to construct a frost protected shallow foundation (FPSF) as a practical alternative to a deeper, more-costly foundation in cold regions with seasonal ground freezing and the potential for frost heave.

Information sheet about insulation retrofits for the hot-dry climate zones.

Information sheet about exterior insulation in the hot-dry climate zones.

Information about a roof retrofit using a metal, cool roof system.

Report covering non-combustible continuous exterior insulation and non-combustible roof venting.

Fact sheet describing the importance of proper roof and deck flashing, and typical and enhanced flashing techniques for coastal homes; also published in FEMA P-499 “Home Builder’s Guide to Coastal Construction: Technical Fact Sheet Series.”

Article describing how insulating and air sealing unfinished attic spaces can lead to reduced energy bills in some homes.

Report describing construction of test homes in Atlanta, GA meeting Building America savings targets and serving as a basis of design for other homes Martin Dodson plans to build within the Serenbe community.

Report evaluating the renovation of a 5,800-ft2, multiuse facility located in St. Petersburg, on the west coast of central Florida, in the hot-humid climate.

High-density sidewall cavity insulation can be a major comfort and savings boost. It saves energy by slowing both conductive and convective losses, but only if the right things are done and done right. This always requires site-specific thinking.

Website providing information about INSULSPAN structurally insulated panels.

How hard can it be to insulate a flat sheet of concrete? I mean you only have three choices – on the top, on the bottom, or on the edge. OK, you might have some combination of the three as well.

Fact sheet describing building envelope performance measures applicable to residential and small commercial construction.

California Energy Commission report presenting the concept of cool walls and providing guidelines for their building- and climate-appropriate use to conserve energy and reduce emissions.

Factsheet describing the use of rigid foam insulation to meet energy efficiency requirements and minimize fire risks.

Job Process sheet for the manufactured housing industry showing how to split and notch insulation batts to fit around electrical boxes and wiring in a factory production environment.

SPFA website homepage.

Literature review from NFPA on the use of insulation to protect the piping in home fire sprinkler systems from freezing conditions.

Guide describing the installation of windows in walls that have foam plastic insulating; guide provides several methods for attaching, supporting, and flashing windows in walls with rigid foam sheathing. (Note: The link only goes to the table of contents for the guide, the full guide can be...

Standard that covers the minimum performance and acceptance criteria for an air barrier (AB) material or system for framed walls of low-rise buildings with the service life of the building wall in mind. This link directs to a preview of the current version of the standard, published in the year 2019...

Standard that covers the minimum performance and acceptance criteria for an air barrier (AB) material or system for framed walls of low-rise buildings with the service life of the building wall in mind. This link directs to a preview of the version of the standard that was published in the year 2011...

Specification covering the standard requirements for application of full thickness Portland cement-based plaster for exterior (stucco) and interior work. This standard was produced in the year 2022, and is available for preview and purchase at the reference link. There are also other versions of...

Specification covering the standard requirements for application of full thickness Portland cement-based plaster for exterior (stucco) and interior work. This standard was produced in the year 2023, and is available for preview and purchase at the reference link. There are also other versions of...

A specification covering the application of Insulating Concrete Forms (ICFs) that act as permanent formwork for cast-in-place reinforced concrete beams & walls which was published in the year 2022 and is available for preview and purchase at the reference link.

Specification describing criteria for manufactured polymeric materials used to provide a rainscreen function, a means for the drainage of liquid moisture and the ventilation of vapor moisture that enters an above-grade exterior wall assembly which was published in the year 2019, and is available for...

This standard specification covers the classification, composition, physical properties, and dimensions of mineral fiber (rock, slag, or glass) blanket intended for use as thermal insulation on surfaces at various temperature ranges. This version of the standard was published in the year 2019 and is...

Information sheet about buried ducts.

Report providing information based on research and case studies, to remodelers and consumers about opportunities to increase home energy performance.

Report following the evolution of the construction quality process from its development for new homes to its application construction of a HPH with enhanced specifications, and its application in a crawlspace renovation.

Document explaining the benefits of evaluating and identifying energy efficiency retrofit measures that could be made during renovation and maintenance of multifamily buildings.

Document serving as a starting point that features initial tools and resources for teams to start collaborating to continually improve the energy efficiency and durability of new houses.

Report covering coating and back venting wood based claddings and trim.