Library

Information sheet about exterior insulation in the hot-dry climate zones.

Report covering non-combustible continuous exterior insulation and non-combustible roof venting.

Fact sheet describing proper roof sheathing installation and illustrating fastening methods that will enhance the durability of a building in high-wind areas; also published in FEMA P-499 “Home Builder’s Guide to Coastal Construction: Technical Fact Sheet Series.”

Factsheet from HUD describing how to properly rebuild following natural disasters in Puerto Rico.

Factsheet from HUD describing how homeowners can retrofit homes following natural disasters in the U.S. Virgin Islands.

Factsheet from HUD describing how to rebuild following natural disasters in Puerto Rico.

Factsheet for builders from HUD on how to rebuild homes following natural disasters in the U.S. Virgin Islands.

Report covering the planning, design, construction, and operation of residential and community safe rooms. Written for architects, engineers, building officials, local officials and emergency managers, and prospective safe room owners and operators.

Article describing how insulating and air sealing unfinished attic spaces can lead to reduced energy bills in some homes.

Report promoting public safety and welfare by reducing the risk of earthquake-induced damage to existing homes.

Report promoting public safety and welfare by reducing the risk of earthquake-induced damage to existing homes.

Report describing construction of test homes in Atlanta, GA meeting Building America savings targets and serving as a basis of design for other homes Martin Dodson plans to build within the Serenbe community.

Report evaluating the renovation of a 5,800-ft2, multiuse facility located in St. Petersburg, on the west coast of central Florida, in the hot-humid climate.

High-density sidewall cavity insulation can be a major comfort and savings boost. It saves energy by slowing both conductive and convective losses, but only if the right things are done and done right. This always requires site-specific thinking.

How hard can it be to insulate a flat sheet of concrete? I mean you only have three choices – on the top, on the bottom, or on the edge. OK, you might have some combination of the three as well.

Fact sheet describing building envelope performance measures applicable to residential and small commercial construction.

Technical report providing site selection guidance for installation of small wind turbines.

Factsheet describing the use of rigid foam insulation to meet energy efficiency requirements and minimize fire risks.

Job Process sheet for the manufactured housing industry showing how to split and notch insulation batts to fit around electrical boxes and wiring in a factory production environment.

SPFA website homepage.

Literature review from NFPA on the use of insulation to protect the piping in home fire sprinkler systems from freezing conditions.

Standard document establishing construction standards for one- and two-family dwellings constructed in high wind regions.

Guide describing the installation of windows in walls that have foam plastic insulating; guide provides several methods for attaching, supporting, and flashing windows in walls with rigid foam sheathing. (Note: The link only goes to the table of contents for the guide, the full guide can be...

This standard specification covers the classification, composition, physical properties, and dimensions of mineral fiber (rock, slag, or glass) blanket intended for use as thermal insulation on surfaces at various temperature ranges. This version of the standard was published in the year 2019 and is...

Information sheet about buried ducts.

A website providing timely and accurate forecasts and watches for severe thunderstorms and tornadoes over the contiguous United States.

Report providing information based on research and case studies, to remodelers and consumers about opportunities to increase home energy performance.

Report recommending strategies and approaches that the Federal government and other stakeholders may take to encourage and aid States and local communities in the adoption of the most current building codes.

Report following the evolution of the construction quality process from its development for new homes to its application construction of a HPH with enhanced specifications, and its application in a crawlspace renovation.

Document serving as a starting point that features initial tools and resources for teams to start collaborating to continually improve the energy efficiency and durability of new houses.

Article describing three ways to strengthen the roof-to-wall connections in an existing home.

Article defining structural design loads and ways to calculate them, including dead loads, live loads, soil lateral loads, wind loads, snow loads, earthquake loads, and other loads.

Conference paper describing testing of the performance of fasteners used to attach rigid foam insulation to the exterior of walls.

Recovery advisory presenting key wind retrofit guidelines for buildings located in hurricane-prone regions. These retrofit guidelines are intended to help building owners and designers prevent or limit wind damage and water infiltration during high-wind events.

Article describing suggested food supplies, sanitation, safety, and cooking for during and after an emergency.

Research study determining how well high performance envelope and innovative cooling system interact to cost effectively reduce cooling energy use in this hot-dry climate.

Research study making several recommendations to whole-home program designers and implementers for improving the cost effectiveness and reach of whole-home programs.

Presentation by the Washington University in St. Louis Office of Sustainability on saving energy.

A guide for homeowners on determining the risks from tornadoes and hurricanes and selecting a safe room type and location, as well as providing detailed plans for safe room construction.

Report presenting safe room designs and showing the homeowner and builder/contractor or local design professional how to construct a safe room for a home or small business.

Brochure describing insulation approaches for homes with slab-on-grade floors.

Brochure with information about how to select and install house wrap and other weather-resistive barriers.

Fact sheet providing the wind resistant provisions of the 2015 International Residential Code.

Article describing a research study exploring how effective interior insulation systems are at keeping basements dry and warm.

Projectile missile testing of various wall panel configuration to understand how the different wall constructions would perform when struck with wind driven debris from a hurricane.

Report illustrating CAD drawings and modeling of bracing layouts for a gable roof truss.

Report descrbing an early study pointing to the significant improvement, >50%, of a hip roof in reducing peak wind-induced pressures.

Manuals describing design, materials, and installation techniques applicable to almost all types of roof systems; four-volume set includes Metal Panel and SPF Roof Systems, Membrane Roof Systems, Architectural Metal Flashing and Condensation and Air Leakage Control, and Steep-Slope Roof Systems.

Report providing a strengths, weaknesses, opportunities, and threats (SWOT) analysis inherent to different models as a way of thinking about the transition from traditional business models into a viable model for delivering deep energy retrofits.

Report about seeking a 30% source energy savings targets over a comparable 2009 International Energy Conservation Code-built home in the cold climate zone, using simple measures.