Library

Information sheet about exterior insulation in the hot-dry climate zones.

Information sheet about HVAC equipment design to maximize energy efficiency in the hot-dry climate zone.

Report covering non-combustible continuous exterior insulation and non-combustible roof venting.

Web page providing an overview of room-level air conditioning systems such as window units and mini-splits.

Article describing how insulating and air sealing unfinished attic spaces can lead to reduced energy bills in some homes.

Technical study exploring the impact of different installation faults on heat pump performance in a single-family house.

Report describing construction of test homes in Atlanta, GA meeting Building America savings targets and serving as a basis of design for other homes Martin Dodson plans to build within the Serenbe community.

Report evaluating the renovation of a 5,800-ft2, multiuse facility located in St. Petersburg, on the west coast of central Florida, in the hot-humid climate.

High-density sidewall cavity insulation can be a major comfort and savings boost. It saves energy by slowing both conductive and convective losses, but only if the right things are done and done right. This always requires site-specific thinking.

Study conducted to help determine cost-effective solutions for heating and cooling houses that are designed to be energy efficient.

How hard can it be to insulate a flat sheet of concrete? I mean you only have three choices – on the top, on the bottom, or on the edge. OK, you might have some combination of the three as well.

Manual that identifies certain leakage limits for ducts and outlines procedures for testing ducts for conformity with air leakage limits that are set forth in a designer’s project specification.

Fact sheet describing building envelope performance measures applicable to residential and small commercial construction.

Webpage describing the STEP campaign encouraging the use of smart diagnostic tools to reduce installation faults.

Fact sheet outlining the research behind how smart ventilation controls boost energy efficiency and indoor air quality, including research findings from seasonal temperature, timer, and real-time weather-based controls showing that all three systems showed potential for energy savings while...

Factsheet describing the use of rigid foam insulation to meet energy efficiency requirements and minimize fire risks.

Job Process sheet for the manufactured housing industry showing how to split and notch insulation batts to fit around electrical boxes and wiring in a factory production environment.

SPFA website homepage.

Literature review from NFPA on the use of insulation to protect the piping in home fire sprinkler systems from freezing conditions.

Proposed HVAC filter labeling standard and underlying analysis by the California Energy Commission.

Standard that defines the roles of and minimum requirements for mechanical and natural ventilation systems and the building envelope intended to provide acceptable indoor air quality in low-rise residential buildings. This version of the standard was published in the year 2016, and is available for...

Standard 680 establishes definitions, classifications, test requirements, data requirements, ratings, operating requirements, marking and nameplate data and conformance conditions for residential air filter equipment.

This Standard provides a consistent, uniform methodology for evaluating the airtightness of building envelopes and heating and cooling air ducts and the air flows of mechanical ventilation systems.

Standard describing methods for testing the airtightness of buildings and HVAC equipment.

Guide describing the installation of windows in walls that have foam plastic insulating; guide provides several methods for attaching, supporting, and flashing windows in walls with rigid foam sheathing. (Note: The link only goes to the table of contents for the guide, the full guide can be...

This standard specification covers the classification, composition, physical properties, and dimensions of mineral fiber (rock, slag, or glass) blanket intended for use as thermal insulation on surfaces at various temperature ranges. This version of the standard was published in the year 2019 and is...

Test method that measures the capture efficiency of wall-mounted domestic range hoods under controlled conditions in a test chambers which available for preview and purchase at the link and was published in the year 2018.

Report addressing barriers to information, contractor resources and cost savings associated with steam balancing multifamily buildings.

Report about results of 10 test buildings in Chicago, studied to identify best practices for methodology, typical costs, and energy savings associated with steam system balancing.

Information sheet about buried ducts.

Report providing information based on research and case studies, to remodelers and consumers about opportunities to increase home energy performance.

Report about the impact on the loads when common safety factors are applied to the load calculation process using two houses that meet the 2009 IECC prescriptive path modeled as the accurate baseline.

Report following the evolution of the construction quality process from its development for new homes to its application construction of a HPH with enhanced specifications, and its application in a crawlspace renovation.

Document covering the pros and cons of compact air distribution systems and the decision criteria that must be considered early in the whole-house design process.

Report describing the equipment selection of a split system air conditioner and furnace for an example house in Chicago, Illinois, as well as a heat pump system for an example house in Orlando, Florida.

Document serving as a starting point that features initial tools and resources for teams to start collaborating to continually improve the energy efficiency and durability of new houses.

Report describing findings from research related to heating, ventilation, and air conditioning (HVAC) companies that have made the decision to transition to whole house performance contracting (WHPC).

Conference paper describing testing of the performance of fasteners used to attach rigid foam insulation to the exterior of walls.

Research study determining how well high performance envelope and innovative cooling system interact to cost effectively reduce cooling energy use in this hot-dry climate.

This document covers a description of the need and applied solutions for supplemental dehumidification in warm-humid climates, especially for energy efficient homes where the sensible cooling load has been dramatically reduced.

Research study making several recommendations to whole-home program designers and implementers for improving the cost effectiveness and reach of whole-home programs.

Question and Answer article in Energy Design Update describing the cost and savings benefits of electronically commutated motors (ECMs) for HVAC equipment.

Report providing performance results of a home's heat pump water heater and whole-house dehumidifier over a six-month period.

The Technician's Guide equips practitioners with the knowledge to properly implement all of the measurement procedures required in the HVAC QI Specification.

This guide and workbook offers practitioners with the knowledge to properly implement the measurement and documentation procedures required in the ANSI/ACCA 5.

Brochure describing insulation approaches for homes with slab-on-grade floors.

Brochure with information about how to select and install house wrap and other weather-resistive barriers.

Article describing a research study exploring how effective interior insulation systems are at keeping basements dry and warm.

Standard providing industry-backed information for assessing new and existing HVAC systems, evaluating and verifying the cleanliness of HVAC system components, preventing job related hazards and guiding the cleaning and restoration of HVAC systems to a specific level of cleanliness.

Report providing a strengths, weaknesses, opportunities, and threats (SWOT) analysis inherent to different models as a way of thinking about the transition from traditional business models into a viable model for delivering deep energy retrofits.