Showing results 1251 - 1300 of 4973
Image
Failure in attic insulation effectiveness caused by wind washing pushing insulation away from the edges of the attic space.
Image
Failure in brick veneer connection under high wind conditions due to anchor corrosion, tie fastener pull-out, failure to embed ties into the mortar, poor bonding between ties and mortar, and poor-quality mortar; on left - five ties not embedded.
Image
Failure of "S" tile roofing in high winds due to bond failure between mortar and tiles.
Image
Failure of a freestanding concrete masonry end wall due to discontinuous tie-beam when exposed to hurricane force winds.
Image
Failure of a garage door due to pressure differences under hurricane force wind conditions resulting in damage to the house.
Image
Failure of barrel tile roofing due to bond failure between underlayment, mortar, and tiles during a hurricane.
Image
Image
Failure of extruded concrete flat tile roofing due to bond failure between tile, mortar, and underlayment resulting from hurricane force winds.
Image
Failure of Roof Structure from Pressurization Due to Window Failure During a Hurricane.
Image
Failure of the wall to roof connection resulted in loss of roof under hurricane force winds.
Image
Fan CFM rating is higher than the requirement increasing the likelihood that it will meet the performance level once installed
Image
Fan CFM rating is higher than the requirement increasing the likelihood that it will meet the performance level once installed
Image
Image
Image
Fan housing was oriented in the correct direction to allow proper exhaust duct installation
Image
Image
Image
Fans from seperate dwellings exhausted together without back-draft dampers and not sealed
Image
Fans supply outdoor air tempered by indoor corridor air to the corridors of a multistory multifamily building, pressurizing the corridors and providing make-up air for the elevator shaft, which is depressurized by an exhaust fan.
Image
Image
Image
Image
Image
Image
FEMA recommends techniques like open lower wall cavities with exterior rigid foam insulation and paperless drywall for flood-resistant, dryable wall interiors.
Image
Image
Ferguson Design and Construction built this custom home in the mixed-humid climate in Long Island, NY, and certified it to DOE Zero Energy Ready Home specifications in 2013.
Image
Ferrier Custom Homes built this custom for buyer home in the hot-humid climate in Aledo, TX, and certified it to DOE Zero Energy Ready Home specifications in 2018.
Image
Ferrier Custom Homes built this custom for buyer home in the hot-humid climate in Fort Worth, TX, and certified it to DOE Zero Energy Ready Home specifications in 2017.
Image
Ferrier Custom Homes built this custom for buyer home in the hot-humid climate in Fort Worth, TX, and certified it to DOE Zero Energy Ready Home specifications in 2020.
Image
Ferrier Custom Homes built this custom for buyer home in the mixed-humid climate in Mineral Wells, TX, and certified it to DOE Zero Energy Ready Home specifications in 2019.
Image
Image
Image
Image
Fiberglass mesh tape is installed around a duct boot in preparation for air sealing with mastic
Image
Image
Image
Fill in the hole left by the missing top plate with a rigid air blocking material or rolled batt insulation that is spray foamed in place
Image
Image
Image
Image
Filter access panel includes gasket or comparable sealing mechanism and fits snugly against the exposed edge of filter when closed to prevent bypass
Image
Filter located and installed so as to facilitate access and regular service by the owner
Image
Finished raised ceiling duct chase
Image
Fire barriers for ventilated wall cavities use thermally activated expansive materials to close off the ventilation space between the wall cladding and the sheathing during a fire while allowing air flow through the metal mesh during normal conditions
Image
Fire barriers for ventilated walls use heat activated intumescent expansive materials to close off the ventilation space between the wall cladding and the sheathing during a fire while allowing air flow through the metal mesh during normal conditions
Image
Fire resistance plans for a community include creating defensible space for each home and for the whole community, constructing with fire-resistant materials, and providing turn-around space for emergency response vehicles.
Image
Fire suppression sprinklers can be set to activate only in the room where a fire is sensed.
Image
Fire-rated sealants or a fire-rated assembly air seal the tops and bottoms of the demising walls between two units in a multifamily building
Image
Fire-rated sealants or a fire-rated assembly air seal the tops and bottoms of the demising walls that separate one dwelling unit from another ina multifamily building