Showing results 101 - 150 of 898
Image
2021 IECC Climate Zone 6B: Vented Over-Roof, Unvented Cathedral Ceiling, 2x6 Wall, Interior Insulated Basement
Image
2021 IECC Climate Zone 7 and 8: Vented Cathedral Ceiling, 2x6 Wall, Interior Insulated Basement (with notes)
Image
Image
2021 IECC Climate Zones 7 and 8: Vented Attic, 2x4 Wall, Interior Insulated Basement
Image
2021 IECC Climate Zones 7 and 8: Vented Attic, Exterior Double Wall, Interior Insulated Basement
Image
2021 IECC Climate Zones 7 and 8: Vented Attic, ICF Wall, ICF Basement Foundation
Image
2021 IECC Climate Zones 7 and 8: Vented Attic, Interior Double Wall, Interior Insulated Basement
Image
2021 IECC Climate Zones 7 and 8: Vented Attic, Strapped 2x6, Interior Insulated Basement
Image
2021 IECC Climate Zones 7 and 8: Vented Cathedral Ceiling, 2x6 Wall, Interior Insulated Basement
Image
2021 IECC Climate Zones 7 and 8: Vented Cathedral Ceiling, 2x6 Wall, Slab on Grade
Image
2021 IECC Climate Zones 7 and 8: Vented Over-Roof, Unvented Cathedral Ceiling, 2x6 Wall, Interior Insulated Basement
Image
A 1- and ½-story home with a room located in the attic and the thermal boundary located at either a) the walls and ceiling of the attic room with small vented attic spaces or b) the roof line for an unvented attic
Image
A builder, energy efficiency consultant, and crew supervisor inspect a spray foam installation.
Image
A concrete slab-on-grade foundation with exterior insulation, which can be elevated above the local grade as a flood-prevention strategy.
Image
A continuous layer of polyethylene covers the crawlspace floor and is attached to the wall with wood nailing strips
Image
A gut rehab that includes drywall removal provides the opportunity to thoroughly insulate the walls.
Image
A low-sloped shed roof with the thermal boundary located at either a) the flat ceiling with a vented attic or b) the roof line for an unvented attic
Image
A nylon draw band and tensioning tool are used to secure the inner coil of the pre-insulated flexible duct
Image
A nylon draw band and tensioning tool are used to secure the inner liner of the pre-insulated flexible duct
Image
A paint-on waterproofing covers the exterior and tops of the concrete block foundation walls and piers to block moisture moving up through the concrete, while foil-faced R-13 insulation lines the inside surface of the exterior walls.
Image
A roof drain is installed in an existing flat roof retrofitted with above-deck rigid foam insulation that is integrated with new air and water control layers
Image
A second layer of rigid insulation is installed over the 2 in. by 4 in. retaining strip
Image
A simple vented attic with good air-sealing of the drywall ceiling air barrier, air flow from soffit vents to ridge vents protected by ventilation baffles, and lots of insulation covering the attic floor is unlikely to encourage ice dams.
Image
A site-built rafter roof with a raised top plate allows for more insulation underneath.
Image
Image
Image
A trained installer completely fills the wall cavities with sprayed cellulose insulation.
Image
A typical Las Vegas hot-dry climate home made of wood frame construction and insulated with R-25 expanded polystyrene externally over a drainage plane, with an unvented wood frame insulated attic and roof assembly.
Image
Adding air-sealing and rigid foam insulation at the wall-to-overhanging floor juncture at the outside corner of an existing home
Image
Advanced framing details include corners that are constructed with fewer studs or studs aligned so that insulation can be installed in the corner.
Image
Advanced framing details include framing aligned to allow for insulation at interior-exterior wall intersections.
Image
Image
Advanced framing details include open headers and reduced framing around windows and two-stud corners to allow more room for insulation in the wall cavities while reducing lumber costs.
Image
Image
Image
Advanced framing techniques including 2x6 walls spaced at 24 inches on center and ladder blocking at wall intersections allow more space for insulation in the wall cavities while open-web floor joists provide space between floors for ducting.
Image
After attaching netting to the 2x6 studs, workers fill the wall cavities with R-23 of blown fiberglass made from recycled bottles.
Image
After securing the inner coil, cover the draw band and the seam with a generous amount of mastic
Image
After setting precast concrete basement walls on an 8-inch bed of trap rock, this builder sprayed 2 inches of closed-cell spray foam directly onto the ground then laid piping for radiant floor heating before pouring the concrete floor slab.
Image
After spraying the 2x6 wall cavities with 2 inches (R-13) of closed-cell spray foam, the walls are covered with netting and an additional 3.5 inches of fiberglass (R-13) is blown in.
Image
Air leaking through the home's envelope wastes a lot of energy and increases energy costs.
Image
Image
Air seal and insulate flex ducts
Image
Image
Air seal floor joist cavities under kneewall with rigid foam, plywood, or OSB caulked in place
Image
Image
Image
Air-Impermeable Insulation for Condensation Control in Unvented Attics, per IRC Table 806.5.
Image
Image
All ceiling, wall, floor, and slab insulation shall achieve RESNET-defined Grade I installation