Library

Report providing builders in marine climates with guidance for building homes that have whole-house energy savings of 40% over the Building America benchmark with no added overall costs for consumers.

Standards book discussing the minimum standards of total system balance of HVAC systems.

Document describing three methods for elevating a home out of the flood zone.

Standard covering equipment sizing loads for single-family-detached homes, small multi-unit structures, condo­miniums, town houses and manufactured homes.

Technical manual from ACCA outlining correct methods for zoning of residential HVAC systems.

Technical report describing the SPS (Structural Panel System), an innovative implementation of the "perfect wall" concept, situating environmental control layers on the exterior side of structural components for improved constructability, cost-effectiveness, and performance, validated through the...

Report analyzing design heating load sizing methods for superinsulated homes in cold climates and comparing them to the actual energy usage to determine if the building load calculation methodology should be changed for calculating the design heating load of these homes.

Article by the Canadian Government on attic ventilation and considerations for moisture and ice dams.

Report covering interior energy retrofits of masonry buildings.

This Best Practices Manual is the product of Hammer & Hand’s ongoing work to document and internally codify our standard operating procedures for construction practice.

Code establishing the rules of safety relating only to pressure integrity for the design, fabrication, and inspection of boilers and pressure vessels during construction which was published in the year 2017 and is available to order at the referenced link.

Code establishing the rules of safety relating only to pressure integrity for the design, fabrication, and inspection of boilers and pressure vessels during construction which was published in the year 2021 and is available to order at the referenced link.

Document focusing on the design and wall components that contribute to a pressure equalized rain screen wall, including the frequency of the weep holes and other brick masonry rain screen wall requirements.

Document providing guidance to U.S. home builders who want to accept the challenge.

Guide describing measures that builders in the cold and very cold climates can take to build homes that have whole-house energy savings of 40% over the Building America benchmark with no added overall costs for consumers.

Web based tool providing decision-making guidance for selecting wall assembly components.

Guidance document providing BA research teams and partners with specific information and approaches to identifying and overcoming potential barriers to Building America (BA) innovations arising in and/or stemming from codes, standards, and rating methods.

Report summarizing research results for the 30% energy savings level and demonstrates that lead builders can successfully provide 30% homes in the Marine Climate Region on a cost-neutral basis.

Document detailing how to build radon-resistant homes.

Training manual on how to locate ducts within conditioned space and compact design.

Article describing the principle of capillarity in construction materials.

Report describing strategies to improve the aging steam heating systems in New York City to improve energy efficiency, reduce oil and gas usage, and cut maintenance costs.

Article describing how closed crawlspaces can do "double duty" by controlling moisture and providing energy savings.

Report outlining the steps developers can take to create high-performance standards on a community-wide scale.

Guidance from Zero Energy Project on construction techniques for warmer climates, such as home orientation, and insulation requirements.

Article about how mortar droppings during the installation of a brick veneer can clog the weep holes in the wall assembly causing moisture damage. The article also illustrates products that can be installed in the ventilated cavity to mitigate this problem.

The Guide addresses walls constructed with 2x4 wood frame studs, wood structural panel (WSP) sheathing as wall bracing and added backing for foam sheathing, a layer of rigid foam sheathing insulation up to 1.5 in. thick over the WSP, and a cladding system installed over the foam sheathing in low...

Part of a larger LBNL report (Deep Energy Retrofit Guidance for the Building America Solutions Center), the Design and Construction Process chapter provides detailed guidance for each process phase: pre-planning, planning, construction, test-out and post-occupancy.

Part of a larger LBNL report (Deep Energy Retrofit Guidance for the Building America Solutions Center), the Lessons Learned chapter focuses on successful deep energy retrofit projects throughout the U.S.

Part of a larger LBNL report (Deep Energy Retrofit Guidance for the Building America Solutions Center), the Occupant Behavior chapter discusses how to assess homeowner behavior patterns and use these patterns to enhance overall energy savings.

Part of a larger LBNL report (Deep Energy Retrofit Guidance for the Building America Solutions Center), the Reducing costs and Increasing Cost-Effectiveness chapter provides suggestions for controlling deep retrofit costs, including both 'do's' and 'don'ts'.

Report covering exterior energy retrofits of masonry buildings.

Report outlining the issues with using existing ducts with a new low-load HVAC system, which reduces throw at supply registers causing decreased mixing of supply and room air, leading to potential thermal comfort complaints.

Report that demonstrates the durability, constructability, and cost-effectiveness of the extended plate and beam (EP&B) wall system for new construction housing projects in compliance with the International Energy Conservation Code, addressing moisture risk management and high-performance envelope...

Report of a field evaluation of four novel roof designs to see how each design would reduce space-conditioned energy use so that the knowledge gained could be applied to the design of new manufactured homes.

Article describing five fundamental changes to building construction from the last 50 years and their modern construction consequences.

A starting point for ballparking and comparing the cost of different siding materials and a brief overview of the pros and cons of different siding materials.

Article describing how omission of two small but critical wall details, a kick-out flashing and a weep screed, lead to extensive water damage to a wall.

Website blog with guidance about calculating heat-loss.

Correcting pressure imbalances in your HVAC system can result in a healthier, more efficient home.

Guide detailing best practices on how to build wall assemblies with absorptive claddings such as brick, stone that drain and dry well.

Central return designs require an open pathway between the room and the heart of the house where the return grill is located.

Article describing walls and moisture development on them.

Standard technical manual with information about HVAC balancing, testing air and hydronic systems.

Webpage featuring hundreds of illustrations of masonry construction details for brick, congrete, stone, tile, stucco, etc.

Article describing the flashing of roofs and what to look for, targeted at home inspectors.

Siding installation guide for Ply Gem Siding Group products.

Fact sheet describing how typical wall moisture barrier systems work, the moisture barrier system and common problems associated with them; also published in FEMA P-499 “Home Builder’s Guide to Coastal Construction: Technical Fact Sheet Series.”

Article describing how moisture accumulates inside of structures and issues that result.

Report providing extensive guidance on controlling moisture in building envelopes through proper selection and installation on air, water, thermal, and vapor barriers.