Library

Standard outlining industry procedure for sizing residential duct systems.

Standard covering equipment sizing loads for single-family-detached homes, small multi-unit structures, condo­miniums, town houses and manufactured homes.

Standard covering sizing strategies for all types of cooling and heating equipment, as well as how to use comprehensive manufacturer’s performance data on sensible, latent, or heating capacity for various operating conditions.

Fact sheet poster describing how to add exterior, continuous, rigid insulation to the exterior walls when replacing siding on an existing home.

Document providing guideance and considerations for duct design in an energy efficient house.

Document focusing on the design and wall components that contribute to a pressure equalized rain screen wall, including the frequency of the weep holes and other brick masonry rain screen wall requirements.

Web based tool providing decision-making guidance for selecting wall assembly components.

Installation manual for installing metal panel siding.

An article illustrating common errors found in fiber cement siding installations. Many of these errors and poor flashing examples apply to siding materials beyond fiber cement siding.

Technical report detailing a study in which actual cooling loads are compared to modeled cooling loads.

Article about how mortar droppings during the installation of a brick veneer can clog the weep holes in the wall assembly causing moisture damage. The article also illustrates products that can be installed in the ventilated cavity to mitigate this problem.

Report covering the rainwater performance of building assemblies.

Report identifying two barriers that limit the ability of builders to explore opportunities for higher levels of energy efficiency in housing: the use of duct system materials that inherently achieve airtightness and are right-sized for low-load houses, and, the ability to air seal fire separation...

Article describing a case study in which a whole-house battery and PV system was tested in a home with cooling and refrigeration during a hurricane in Florida.

An example of a commercially available thermally expansive fire stopping product for controlling the spread of fires in a rainscreen cavity.

Report covering the fire performance of combustible cladding over combustible insulation.

Guide by the Northeast Energy Efficiency Partnerships on how to size heat pumps in a cold climate.

Presentation about proper installation of flexible ducts.

A article about the best practice method of installing fiber cement siding, to install flashing at the butt joints of the siding boards, rather than face caulking the butt joints afterwards.

Factsheet describing re-siding retrofits containing exterior insulation and window upgrades aimed at improved energy savings and comfort.

Guide detailing best practices on how to build wall assemblies with absorptive claddings such as brick, stone that drain and dry well.

Article describing what evaporative coolers are, how they work, different types, performance, where they are appropriate, and how to install and maintain them.

Report covering reservoir claddings, back ventilation and vapor throttles.

Article providing guidance for installing manufactured stone veneer, including information on rainscreens.

Webpage featuring hundreds of illustrations of masonry construction details for brick, congrete, stone, tile, stucco, etc.

Report providing step-by-step instructions for heating contractors and hydronic designers for selecting the proper control settings to maximize system performance and improve response time when using a thermostat setback.

Report providing extensive guidance on controlling moisture in building envelopes through proper selection and installation on air, water, thermal, and vapor barriers.

A study on how fires spread through exterior building envelopes with discussion on how fires propagate in a rain screen cavity.

An example of a form a building codes department created to ensure builders are fully aware and have taken steps to provide drainage so that water doesn’t accumulate behind siding. This example is from the city of Newberg, Oregon.

Technical report describing the Re-Side Right initiative by the New Jersey Institute of Technology's Building America research team that proposes enhancing home efficiency during the re-siding process by incorporating an insulating layer that acts as both an air barrier and water resistive barrier...

Report describing the testing of various siding materials for their ability to resist bullets from small firearms.

Website providing the pros and cons of different siding materials for home building, including wood, vinyl, fiber cement, stucco, brick, metal, and stone.

Information sheet describing how to select a properly sized water heater based on household usage patterns, peak demand, and heater type—whether tankless, solar, or storage-based—to ensure efficiency and adequate hot water supply.

A website providing information on how to properly size a water heater based on tank size, volume, peak hour demand and other factors.

Web page describing the basics of how to size and build a battery bank for electricity storage.

Manual describing the installation process for Craneboard insulated vinyl siding; while installation is similar across insulated vinyl siding products, see manufacturers for specific guidance.

Specification describing criteria for manufactured polymeric materials used to provide a rainscreen function, a means for the drainage of liquid moisture and the ventilation of vapor moisture that enters an above-grade exterior wall assembly which was published in the year 2019, and is available for...

Report covering coating and back venting wood based claddings and trim.

A story about bees building a hive in the drainage plane behind the brick veneer siding. The bees entered the wall through unprotected drainage holes.

Projectile missile testing of various wall panel configuration to understand how the different wall constructions would perform when struck with wind driven debris from a hurricane.

Users guide to help contractors and homeowners use the Cold Climate Heat Pump Sizing Support Tools developed by NEEP to size and select the best air source heat pumps for their cold climate location.

A presentation about the need for rainscreens including the damage water and moisture ingress into a home’s siding and framing can cause, and ways to design a resilient wall that drains and ventilates well.

An article written by Don Jackson of The Journal of Light Construction on how to detail brick veneer siding wall.