Library

Article from Washington Post on passive cooling measures for homes during extreme heat.

Article describing how omission of two small but critical wall details, a kick-out flashing and a weep screed, lead to extensive water damage to a wall.

Article from Montana State University Extension explaining how proper insulation techniques can greatly reduce the risks of ice dams on roofs in cold climate zones.

Factsheet describing proper methods for installing vinyl siding and soffit coverings in high wind and coastal areas.

Checklist for verifying FORTIFIED levels and documentation needed.

A structural insulated panel (SIP) roof has no embedded lumber in the structure, and therefore nothing substantial for attaching PV array and solar hot water mounts. Single or double lumber splines could be put into the panels, or I-joists at 4-foot intervals could be added.

Code describing the requirements for existing site-built single-family homes to receive roof-to-wall retrofits when re-roofing.

A document aimed at reducing the vulnerability of a gable end roof to wind damage in a hurricane.

Report describing the hurricane retrofit guide with focus on walls and wooded framed walls.

Wildfire guidance for homes located in the wildland urban interface, focused on site design and individual pieces of the home.

Ignition resistant residential construction and landscaping guidelines from FireSafe Montana.

An impact test report from projectile missile tests against brick veneer, verifying that brick veneers perform well to resisting hurricane force wind driven debris.

Article describing the effect metal roofs have on thermal performance in hot-humid climates.

Site showing flame spread ratings and definitions for common building materials.

Article from Building Science Corporation explaining 'wash and wear buildings' that are designed to be flooded and washed out afterwards.

PDF detailing the inspection and verification guidance for WaterSense labeled new homes including indoor and outdoor efficiency requirements, and homeowner and building management education.

Report providing general guidelines for the installation of rolled erosion control products.

Article describing the second step of a three-step process for the installation a tubular skylight, using peel-and-stick flashing tape instead of roof cement, and integrating the roof underlayment with the flashing.

Article describing how to counterflash a chimney by tucking the upper pieces of counterflashing into the chimney mortar joints and overlapping them over the various pieces of base flashing, which are nailed to the roof deck.

Article describing the insurance savings of a home with a hip roof versus a gable roof from the perspective of an insurance advisor.

Article describing how the configuration of surrounding buildings affects the wind loads on a hip roof in a low-rise building.

Report discussing how to create livable space in the attic that meets IRC code requirements by either creating a ventilated roof assembly, or and unvented attic assembly.

Report describing ways to retrofit a home to make it more hurricane resistant.

Article showing steps for kick out flashing at roof-wall intersection.

EPA’s 2008 Lead-Based Paint Renovation, Repair and Painting (RRP) Rule (as amended in 2010 and 2011), aims to protect the public from lead-based paint hazards associated with renovation, repair and painting activities.

Article describing a technique for installing a skylight and avoiding potential water leaks with the use of a peel-and-stick (or self-adhesive) membrane under the flashing.

Web article describing many ways homeowners, contractors, and builders can make homes more resistant to hurricanes, tornadoes, high winds, floods, and hail.

Webpage featuring hundreds of illustrations of masonry construction details for brick, congrete, stone, tile, stucco, etc.

Fact sheet describing important roof-to-wall and wall-to-foundation connection details for masonry construction in coastal areas, including load paths, building materials, and reinforcement; also published in FEMA P-499 “Home Builder’s Guide to Coastal Construction: Technical Fact Sheet Series.”

Article describing the flashing of roofs and what to look for, targeted at home inspectors.

Article describing methods for insulating and air sealing vented and unvented roofs in various climates zones.

This Measure Guideline provides design and construction information for a deep energy enclosure retrofit solution of a flat roof assembly.

Study investigating measured cooling energy savings in homes across the U.S. from the installation of roofing with higher solar reflectance.

A presentation describing the standards regarding who is responsible for what part of the design to ensure the roof truss is properly designed and braced.

An installation training manual discussing the installation of metal roofing materials and related accessories, for both new construction and retrofit projects.

A Recovery Advisory guide reccomending practices for designing and installing metal roof systems that will enhance wind resistance in high-wind regions (i.e., greater than 90-miles per hour [mph] gust design wind speed).

Report covering the selection of roof vents for rainwater resistance.

FEMA mitigation assessment team report following Hurricane Charley in Florida including observations, recommendations, and technical guidance for retrofitting hurricane-damaged homes.

FEMA mitigation assessment team report following Hurricane Ivan in Florida and Alabama including observations, recommendations, and technical guidance.

This report requires all elements of rooftop PV panel systems to be designed for component and cladding pressures per ASCE 7-10.

Report providing extensive guidance on controlling moisture in building envelopes through proper selection and installation on air, water, thermal, and vapor barriers.

EPA guidance document providing information on moisture control in buildings.

Brochure discussing specific practices for mitigating moisture and mold during the construction process.

Online course describing mold and mold remediation for environmental and public health professionals.

Document describing common questions about moisture, mold, and wood.

Standard covering overs mounting systems, including mounting devices, clamping devices and ground lugs for use with photovoltaic modules and panels and contains requirements for ground-mounted and roof systems as part of a nonstructural building component.

Article describing mulch requirements and benefits.

Pamphlet describing different types of mulches and their benefits.

Information sheet with nail withdrawl capacities in OSB.

Guide providing information on controlling attic ductwork sweating.