Library

Report briefly reviewing past research on the effects of occupant behavior on residential energy use and then covering a two year pilot evaluation of a low cost residential energy feedback system installed in twenty case study homes in Florida.

Report briefly reviewing past research on the effects of occupant behavior on residential energy use and then covering a two year pilot evaluation of a low cost residential energy feedback system installed in twenty case study homes in Florida.

Manual describing design, detailing, material selection and troubleshooting for plaster, IEFs, and drywall, with information on continuous insulation, air barriers, rain screens, and ratings for fire and sound.

Report designed to help a builder understand quality management and its role in transitioning from conventional to HPH building and remodeling.

Report proposes high performance duct measures for inclusion in California Title 24 building energy efficiency standards for 2016.

Paper covering a parametric study of foundation heat exchanger-based ground source heat pump systems for several house configurations in a range of European locations, with an emphasis on determining feasible combinations.

Report summarizing the results of laboratory testing of 20 advanced power strip products.

Report describing extensive renovations to a historic home.

Report about a tool developed to enable users to compare a typical 1970s ranch home against an IECC 2009 code-compliant home of the same configuration and against the 70s base case plus retrofits.

Research report detailing Florida Solar Energy Center (FSEC) partnership with Manatee County Habitat for Humanity to design a compact, Zero Energy Ready Home in Florida, tackling challenges like equipment sizing and indoor air quality, offering insights for projects surpassing building code...

Reports describing a mathematical methodology for assessing the seismic performance of buildings.

Article outlining the key issues related to the protection of the building envelope against seismic forces.

Report summarizing commissioning, short-term testing, and analysis that occurred before, during, and just after the actual retrofit of the Bay Ridge project.

High-density sidewall cavity insulation can be a major comfort and savings boost. It saves energy by slowing both conductive and convective losses, but only if the right things are done and done right. This always requires site-specific thinking.

Manual that identifies certain leakage limits for ducts and outlines procedures for testing ducts for conformity with air leakage limits that are set forth in a designer’s project specification.

Fact sheet describing building envelope performance measures applicable to residential and small commercial construction.

California Energy Commission report presenting the concept of cool walls and providing guidelines for their building- and climate-appropriate use to conserve energy and reduce emissions.

Research study presenting a unique opportunity to both identify and evaluate deep retrofit measures that are practical and potentially cost effective for the retrofit market, as well as review the cost effectiveness of the Passive House design approach for achieving energy savings in deep retrofits.

Job Process sheet for the manufactured housing industry showing how to split and notch insulation batts to fit around electrical boxes and wiring in a factory production environment.

Standard describing methods for testing the airtightness of buildings and HVAC equipment.

Test method designed to calculate an assigned air permeance of flexible sheet or rigid panel-type materials at a reference air pressure differential of 75 Pa which was published in the year 2021 and is available for preview and purchase at the reference link.

Standard describing a test method measuring air-leakage rates through a building envelope under controlled pressurization and de-pressurization which was published in the year 2019 and is available for preview and purchase at the reference link.

Test method providing a rapid means of determining the steady-state thermal transmission properties of thermal insulations and other materials with a high level of accuracy when the apparatus has been calibrated appropriately. This version of the standard was published in the year 2021 and is...

ASTM standard test method for surface burning response of different building materials which was published in the year 2022 and is available for preview and purchase at the reference link.

ASTM standard test method for testing the surface burning response of different building materials which was published in the year 2023 and is available for preview and purchase at the reference link.

Standard that describes the principles for the design of a hot box apparatus and the minimum requirements for the determination of steady state thermal performance of building assemblies when exposed to controlled laboratory conditions. The current version of the standard was published in 2019, and...

Test method designed to obtain reliable values for the WVTR of plastic film and sheeting which was published in the year 2020 and is available for preview and purchase at the reference link.

Standard describing two techniques for measuring air leakage rates through a building envelope in buildings that may be configured to a single zone which was published in the year 2022 and is available for preview and purchase at the reference link.

Report intending to provide useful information as the DOE/BA develops and implements comprehensive communications and outreach strategies for demonstration homes.

Information sheet describing correct application of stucco.

Report evaluating a test home built in Atlanta, GA in the mixed-humid climate zone. The report outlines the features of the house, discusses the implementation of the energy efficient design, and presents the results of short-term characterization testing.

Document about NREL's repository of residential building characteristics and historical energy use data, used to improve accuracy of residential energy analysis tools.

Report using data from various sources to characterize the impact on human health and property damage from indoor environmental quality and other hazards.

FSEC certification and testing page for solar systems.

Report describing use of the Energy in Modular (EMOD) method to design, produce, and deliver affordable, net-zero energy, low-carbon, and healthier buildings through industrialized (factory) construction of modular buildings; modeling of whole buildings and subassemblies of components, pods, panels...

Document providing an overview of the Thermal Bypass Checklist for the ENERGY STAR Qualified Homes program.

Guide describing details that serve as a visual reference for each of the line items in the Thermal Enclosure System Rater Checklist.

Report proposing a procedure for estimating the whole opaque wall R-value (whole-wall R-value), independent of system type and construction materials.

Technical report describing the impact of thermal bridging in balcony connections, presenting alternative design strategies, performance analyses, and case studies to enhance energy efficiency and reduce carbon emissions in building envelopes.

BSD-102 report providing guidance about whether to construct a vented or unvented attic based on hygro-thermal zone.

Report focusing on the performance and durability of unvented-cathedralized attics in hot-humid climates with both tile and asphalt shingle roofing.

Report addressing the ever increasing percentage of whole house energy use that is attributable to miscellaneous electricity loads (MELs) and major appliances.

Document describing the measured annual performance data from 12 recent-vintage very low energy homes in the US.

Report assessing the performance and cost-effectiveness of a zero net energy community project in Davis, CA.

Factsheet describing the importance of system charging, superheat and subcooling.

Introductory guide to air sealing the envelope of a home to reduce wasted energy and save on energy costs.

Research study describing an evaluation of selected windows undertaken by IRC researchers at Ottawa’s Laurier House (now being used as a museum) to determine their effectiveness in controlling condensation.