Library

Fact sheet describing a novel, simplified air delivery system using a plug-and-play model that features 3-inch diameter flexible ducts, efficient fittings, and a simplified installation process that resulted in successful market engagement through commercialization.

Document about development of recommendations to help residential HVAC designers select optimal supply inlet size and system operating conditions to maintain good thermal comfort in low heating and cooling load homes.

Research study using modeling to determine optimal combination(s) of components/pumps, high efficiency heat sources, plumbing configurations and controls that result in the highest overall efficiency for a hydronic system.

Report covering wind loading on roofing assemblies.

DOE case study findings on raised ceiling interior duct systems.

Report including an overview of the buried duct research and information the retrofit methodology used to install and test the three existing duct systems, including short- and long-term data collection.

Document presenting results from testing prototype HVAC duct system designs that would locate the entire length of duct work within the air and thermal barriers of the building envelope. These include one that incorporated a high-side supply register, one that utilized a single soffit located within...

Presentation providing information about correctly installing ductwork in new and existing homes.

Report proposes high performance duct measures for inclusion in California Title 24 building energy efficiency standards for 2016.

Research study about a high performance retrofit of an existing brick building (a former convent) into condominiums, all affordable housing.

Report describing procedures for increasing sensible efficiencies through increased flow rates across the air handling unit and increased indoor coil sizes.

Report about cost effective energy-efficient upgrades that can be implemented in the hot, dry Southwest climate.

Document reviewing current and potential ventilation technologies for residential buildings with particular emphasis on North American climates and construction.

Fact sheet describing proper roof sheathing installation and illustrating fastening methods that will enhance the durability of a building in high-wind areas; also published in FEMA P-499 “Home Builder’s Guide to Coastal Construction: Technical Fact Sheet Series.”

Article describing how insulating and air sealing unfinished attic spaces can lead to reduced energy bills in some homes.

Report describing development of a package of energy efficiency measures to achieve 60% energy savings in a test house.

Website with consumer information about duct cleaning.

Manual that identifies certain leakage limits for ducts and outlines procedures for testing ducts for conformity with air leakage limits that are set forth in a designer’s project specification.

Fact sheet describing building envelope performance measures applicable to residential and small commercial construction.

This Standard provides a consistent, uniform methodology for evaluating the airtightness of building envelopes and heating and cooling air ducts and the air flows of mechanical ventilation systems.

Guide describing the installation of windows in walls that have foam plastic insulating; guide provides several methods for attaching, supporting, and flashing windows in walls with rigid foam sheathing. (Note: The link only goes to the table of contents for the guide, the full guide can be...

Report addressing barriers to information, contractor resources and cost savings associated with steam balancing multifamily buildings.

Information sheet about buried ducts.

Report about the impact on the loads when common safety factors are applied to the load calculation process using two houses that meet the 2009 IECC prescriptive path modeled as the accurate baseline.

Document covering the pros and cons of compact air distribution systems and the decision criteria that must be considered early in the whole-house design process.

Report about proper water heater selection developed to provide step-by-step procedures for evaluating preferred cost-effective options for energy efficient water heater alternatives based on local utility rates, climate, and anticipated loads.

Report describing findings from research related to heating, ventilation, and air conditioning (HVAC) companies that have made the decision to transition to whole house performance contracting (WHPC).

Conference paper describing testing of the performance of fasteners used to attach rigid foam insulation to the exterior of walls.

Information sheet describing correct application of stucco.

Discussion of building sheathing.

Standard providing industry-backed information for assessing new and existing HVAC systems, evaluating and verifying the cleanliness of HVAC system components, preventing job related hazards and guiding the cleaning and restoration of HVAC systems to a specific level of cleanliness.

Article describing the evolution of the IRC to permit class 3 vapor retarders (latex paint) in walls coupled with exterior continuous insulation to allow drying and reduce condensation risk.

Case study about a structural sheathing product composed of enhanced EPS rigid foam with OSB adhered on one side.

Information sheet describing transfer ducts and grilles for HVAC.

Research study comparing TRNSYS Type 604 pipe model against laboratory pipe heat loss test data and detailed field monitoring data.

Information sheet about proper ventilation and air sealing.

Guide providing information on controlling attic ductwork sweating.

Report describing the design and construction of a highly energy efficient community of ten duplexes in Greenfield, Massachusetts.

Report and case study describing a retrofit project for single family homes in the Pacific Northwest.