Library

2009 edition of code for commercial buildings that brings together all structural, plumbing, mechanical, fuel gas, energy and electrical provisions for all buildings except detached one- and two-family residences and townhouses up to three stories.

2009 edition of code establishing a baseline for the design and installation of fuel gas systems and gas fired appliances through performance requirements.

2009 edition of code establishing minimum regulations for plumbing facilities, including fixtures, water heaters, water supply and distribution, sanitary drainage, storm drainage, etc.

2009 edition of code for residential buildings that creates minimum regulations for one- and two-family dwellings of three stories or less, bringing together all building, plumbing, mechanical, fuel gas, energy and electrical provisions for one- and two-family residences.

2012 edition of code establishing minimum regulations for plumbing facilities, including fixtures, water heaters, water supply and distribution, sanitary drainage, storm drainage, etc.

Florida building code including all the amendments and additions by Florida for the wind-borne debris regions and the high-velocity hurricane zone.

Document describing portions of the flood provisions from the 2018 editions of the IBC, IRC, IEBC, IMC, IPC, IFGC, IFC, ISPSC, IPSDC, and ICC Performance Code.

Code set from IAPMO explaining plumbing standards. 2018 publication.

This Standard establishes the minimum requirements to evaluate a residence with regards to energy efficiency, water conservation, occupant comfort, and indoor air quality.

Code establishing the rules of safety relating only to pressure integrity for the design, fabrication, and inspection of boilers and pressure vessels during construction which was published in the year 2017 and is available to order at the referenced link.

Webinar answering code-related questions on duct leakage tests, moisture levels in attics and crawlspaces, combustion equipment in conditioned attics, ventilation in multifamily buildings, and continuous insulation in residential construction.

Report examining the cost differences between a typical home and a home constructed using wildfire-resistant materials and design features.

Part I of the Guide addresses walls constructed with 2x6 wood frame studs, wood structural panel (WSP) sheathing as exterior sheathing, gypsum board as interior sheathing, and a cladding system installed over WSP sheathing in low-rise residential buildings up to three stories in height. Walls with...

A quick guide from the California Division of the State Architect (DSA) explaining the three types of gas shutoff devices to stop the flow of natural gas into buildings in the event of an earthquake or rupture of the gas line.

Handbook to help property owners understand the rules, procedures, standards, and criteria that apply to the environmental resource permit (ERP) program under Part IV of Chapter 373 of the Florida Statutes.

Document discussing methods to bioengineer stabilization of shorelines using living and non-living plant materials in combination, known as the “Living Shorelines” concept.

Webpage describing federal regulation related to excess flow valves on residential natural gas lines.

Website with articles on home ventilation and indoor air quality.

Website providing the technical specifications and related documents for home builders, subcontractors, architects, and other housing professionals interested in certifying a home to the EPA's Indoor airPLUS program requirements.

2017 version of a standard covering requirements for single- and dual-pane windows, glazed side-hinged door systems, sliding doors, tubular daylighting devices, and unit skylights developed jointly by the American Architectural Manufacturers Association (AAMA), the Canadian Standards Association...

A presentation describing the standards regarding who is responsible for what part of the design to ensure the roof truss is properly designed and braced.

A document providing guidance on integrating a PV array with a roof system.

Guide describing ways builders can block off entry points and otherwise make homes inhospitable to all manner of pests.

Standard using deficiency-based and systematic procedures that use performance-based principles to evaluate and retrofit existing buildings to withstand the effects of earthquakes. The current version of this standard was published in the year 2017, and is available in both digital and print...

Factsheet describing the use of rigid foam insulation to meet energy efficiency requirements and minimize fire risks.

Website providing a link for purchasing NFPA 1141, Standard for Fire Protection Infrastructure for Land Development in Wildland, Rural, and Suburban Areas.

Website providing a link for purchasing NFPA 703, Standard for Fire Retardant—Treated Wood and Fire–Retardant Coatings for Building Materials.

Standard 680 establishes definitions, classifications, test requirements, data requirements, ratings, operating requirements, marking and nameplate data and conformance conditions for residential air filter equipment.

Website providing a link for purchasing NFPA 1144, Standard for Reducing Structure Ignition Hazards from Wildland Fire.

Standard specification covering the properties of a cured single- or multicomponent cold-applied elastomeric joint sealant for sealing, caulking, or glazing operations on buildings, plazas, and decks for vehicular or pedestrian use, and types of construction other than highway and airfield pavements...

Test method that measures the capture efficiency of wall-mounted domestic range hoods under controlled conditions in a test chambers which available for preview and purchase at the link and was published in the year 2018.

The 2017 publication update to the SEAOC Wind Committee and SEAOC Solar Photovoltaic Systems Sub-Committee's 2012 report.

Fact sheet describing best practices for flashing doors and windows to minimize air and water intrusion.

Document with information on preventing termites when using ICFs.

NAFA’s user guide for understanding ANSI/ASHRAE Standard 52.2-2012.