Skip to main content

Resources

Explore a library of home construction and renovation guidance and easily search through galleries containing hundreds of building science-related photos, drawings, videos, CAD files, case studies, and presentations.

Skip to results

Filter

View Library

Showing 7201 - 7224 of 7387 results:

Filters

Image:

Wrong – The below-grade concrete walls do not have any damp-proof coating

Wrong – The below-grade concrete walls do not have any damp-proof coating
Image:

Wrong – The blower door is installed improperly with a gap at the corner and along the side of the frame that will allow air leakage and could allow the frame apparatus to become dislodged during testing

Wrong – The blower door is installed improperly with a gap at the corner and along the side of the frame that will allow air leakage and could allow the frame apparatus to become dislodged during testing
Image:

Wrong – The blower door pressure reference hose (blue) ends too close to the outdoors side of the fan. Air moving across the end of the hose will affect the pressure reading

Wrong – The blower door pressure reference hose (blue) ends too close to the outdoors side of the fan. Air moving across the end of the hose will affect the pressure reading
Image:

Wrong – The building felt is not installed on the entire house

Wrong – The building felt is not installed on the entire house
Image:

Wrong – The cabinets and drawers were not outfitted properly with mechanical or self-locking latches, causing them to swing open and spill their contents onto the floor.

Wrong – The cabinets and drawers were not outfitted properly with mechanical or self-locking latches, causing them to swing open and spill their contents onto the floor.
Image:

Wrong – The clips holding these metal roofing panels were set too far from the roof eave (above red line) and the panels lifted in strong winds

Wrong – The clips holding these metal roofing panels were set too far from the roof eave (above red line) and the panels lifted in strong winds
Image:

Wrong – The corners are not properly flashed, leaving a vulnerable area in the drainage system

Wrong – The corners are not properly flashed, leaving a vulnerable area in the drainage system
Image:

Wrong – The cripple wall beneath this house failed in an earthquake

Wrong – The cripple wall beneath this house failed in an earthquake
Image:

Wrong – The damaged rim joist was not replaced and its strength is compromised in a critical load-bearing corner.

Wrong – The damaged rim joist was not replaced and its strength is compromised in a critical load-bearing corner.
Image:

Wrong – The damper leading to the ductwork for a central ERV is closed during a duct leakage test; the duct tester is attached to the ERV cabinet, so this will only measure the air tightness of the ERV cabinet and not the duct system

Wrong – The damper leading to the ductwork for a central ERV is closed during a duct leakage test; the duct tester is attached to the ERV cabinet, so this will only measure the air tightness of the ERV cabinet and not the duct system
Image:

Wrong – The downspout terminates too close to the foundation of the house

Wrong – The downspout terminates too close to the foundation of the house
Image:

Wrong – The drain tile is cut and now does not extend around the entire foundation footing

Wrong – The drain tile is cut and now does not extend around the entire foundation footing
Image:

Wrong – The drain tile is not installed to terminate properly and will not transport water to the exterior

Wrong – The drain tile is not installed to terminate properly and will not transport water to the exterior
Image:

Wrong – The drain tile is not wrapped in fabric and could become clogged with debris

Wrong – The drain tile is not wrapped in fabric and could become clogged with debris
Image:

Wrong – The duct for this kitchen exhaust fan is made of flex duct instead of smooth metal duct and the duct is not properly supported.

Wrong – The duct for this kitchen exhaust fan is made of flex duct instead of smooth metal duct and the duct is not properly supported.
Image:

Wrong – the exhaust terminal for a clothes dryer should not be covered with a screen which could trap lint; instead, cover it with a hooded, louvered damper

Wrong – the exhaust terminal for a clothes dryer should not be covered with a screen which could trap lint; instead, cover it with a hooded, louvered damper
Image:

Wrong – The final grade does not slope away from the house

Wrong – The final grade does not slope away from the house
Image:

Wrong – The flashing of the roof-wall juncture was installed above the roof shingles instead of below the roof shingles; also no kickout flashing was installed.

Wrong – The flashing of the roof-wall juncture was installed above the roof shingles instead of below the roof shingles; also no kickout flashing was installed.
Image:

Wrong – The flashing tape was not installed with a roller to completely adhere it to the OSB sheathing surface.

Wrong – The flashing tape was not installed with a roller to completely adhere it to the OSB sheathing surface.
Image:

Wrong – The footers of this house were not deeper than the depth of scour during a flood, causing undermining of the foundation

Wrong – The footers of this house were not deeper than the depth of scour during a flood, causing undermining of the foundation
Image:

Wrong – The footing drain pipe should end at least 10 feet from the foundation if above ground or should drain into a drywell or storm sewer.

Wrong – The footing drain pipe should end at least 10 feet from the foundation if above ground or should drain into a drywell or storm sewer.
Image:

Wrong – The framing and wind baffle installation will not allow for required insulation depth.

Wrong – The framing and wind baffle installation will not allow for required insulation depth.
Image:

Wrong – The framing will not allow for required insulation depth.

Wrong – The framing will not allow for required insulation depth.
Image:

Wrong – The gable end wall failed because the rigid foam sheathing was not backed up by plywood or OSB.

Wrong – The gable end wall failed because the rigid foam sheathing was not backed up by plywood or OSB.