Skip to main content

Resources

Explore a library of home construction and renovation guidance and easily search through galleries containing hundreds of building science-related photos, drawings, videos, CAD files, case studies, and presentations.

Filter

View Library

Showing 457 - 480 of 726 results:

Image:

Right – The recessed can light penetration is sealed with caulk to the drywall.

Right – The recessed can light penetration is sealed with caulk to the drywall.
Image:

Right – The rim joists above the pre-insulated basement walls are sealed and insulated with spray foam to prevent air leakage at this juncture in the building envelope.

Right – The rim joists above the pre-insulated basement walls are sealed and insulated with spray foam to prevent air leakage at this juncture in the building envelope.
Image:

Right – The rough opening around the window has been filled with low-expansion foam to air seal.

Right – The rough opening around the window has been filled with low-expansion foam to air seal.
Image:

Right – The rough opening around window has been filled with backer-rod to air seal.

Right – The rough opening around window has been filled with backer-rod to air seal.
Image:

Right – The sill plate was sprayed with foam prior to installation atop foundation.

Right – The sill plate was sprayed with foam prior to installation atop foundation.
Image:

Right – There is a foam gasket installed between the sill plate and foundation.

Right – There is a foam gasket installed between the sill plate and foundation.
Image:

Right – These neatly cut holes have been properly sealed with caulk and foam.

Right – These neatly cut holes have been properly sealed with caulk and foam.
Image:

Right – This attic knee wall and the floor joist cavity openings beneath it are being sealed and insulated with spray foam.

Right – This attic knee wall and the floor joist cavity openings beneath it are being sealed and insulated with spray foam.
Image:

Right – This hole has been neatly cut and properly sealed with foam.

Right – This hole has been neatly cut and properly sealed with foam.
Image:

Right – This ICAT recessed light is sprayed with foam to act as gasket against the drywall.

Right – This ICAT recessed light is sprayed with foam to act as gasket against the drywall.
Image:

Right – This neatly cut hole has been properly sealed with foam.

Right – This neatly cut hole has been properly sealed with foam.
Image:

Right – This recessed light is ICAT labeled, but still needs a gasket.

Right – This recessed light is ICAT labeled, but still needs a gasket.
Image:

Right – This recessed light was installed with a trim kit and is ICAT labeled.

Right – This recessed light was installed with a trim kit and is ICAT labeled.
Image:

Right – This seam along a common wall is air sealed.

Right – This seam along a common wall is air sealed.
Image:

Right – Top and bottom plates were installed prior to backing and insulation.

Right – Top and bottom plates were installed prior to backing and insulation.
Image:

Right – Top plate to drywall connection sealed from attic with caulk

Right – Top plate to drywall connection sealed from attic with caulk
Image:

Right – Top plate to drywall connection sealed from attic with foam

Right – Top plate to drywall connection sealed from attic with foam
Image:

Right – Top plate to drywall connection sealed from attic with foam sealant

Right – Top plate to drywall connection sealed from attic with foam sealant
Image:

Right – Transfer grilles are installed over doorways to bedrooms in a new-construction home

Right – Transfer grilles are installed over doorways to bedrooms in a new-construction home
Image:

Right – Vent and air barrier sealed

Right – Vent and air barrier sealed
Image:

Right – Verify continuous rigid insulation is installed

Right – Verify continuous rigid insulation is installed
Image:

Right – Verify single member headers with insulation on one side are installed

Right – Verify single member headers with insulation on one side are installed
Image:

Right – Verify SIP headers are installed

Right – Verify SIP headers are installed
Image:

Right – Verify two member headers with rigid insulation between are installed

Right – Verify two member headers with rigid insulation between are installed