Skip to main content

Resources

Explore a library of home construction and renovation guidance and easily search through galleries containing hundreds of building science-related photos, drawings, videos, CAD files, case studies, and presentations.

Filter

View Library

Showing 2017 - 2040 of 2057 results:

Image:

Wrong – These plumbing penetrations have been cut larger than needed, making them difficult to seal.

Wrong – These plumbing penetrations have been cut larger than needed, making them difficult to seal.
Image:

Wrong – This cabin has a gap between the concrete slab and the wall where rodents can enter

Wrong – This cabin has a gap between the concrete slab and the wall where rodents can enter
Image:

Wrong – This chimney pillow does not completely block the flue shaft; there is a lot of open space for air to continue leaking

Wrong – This chimney pillow does not completely block the flue shaft; there is a lot of open space for air to continue leaking
Image:

Wrong – This duct boot is not sealed to the wall board

Wrong – This duct boot is not sealed to the wall board
Image:

Wrong – This duct boot is sealed inside the boot for a duct leakage test; this fails to account for the ductwork leakage between the duct boot and the wall board

Wrong – This duct boot is sealed inside the boot for a duct leakage test; this fails to account for the ductwork leakage between the duct boot and the wall board
Image:

Wrong – This ductwork is not sealed where the round duct is attached to the square duct riser

Wrong – This ductwork is not sealed where the round duct is attached to the square duct riser
Image:

Wrong – This electric wiring hole was filled with foam that is not protected with copper mesh or hardware cloth so rodents could chew through the foam and enter the house (see Solution Center Guide "Reduce Pest Intrusion").

Wrong – This electric wiring hole was filled with foam that is not protected with copper mesh or hardware cloth so rodents could chew through the foam and enter the house (see Solution Center Guide "Reduce Pest Intrusion").
Image:

Wrong – This hole has not been air-sealed.

Wrong – This hole has not been air-sealed.
Image:

Wrong – This metal duct is crushed, is sealed with duct tape instead of mastic or UL-181 metal tape, and is not correctly supported.

Wrong – This metal duct is crushed, is sealed with duct tape instead of mastic or UL-181 metal tape, and is not correctly supported.
Image:

Wrong – This recessed can light has not been sealed to the drywall.

Wrong – This recessed can light has not been sealed to the drywall.
Image:

Wrong – This recessed light does not have a gasket installed.

Wrong – This recessed light does not have a gasket installed.
Image:

Wrong – This recessed light is not ICAT labeled.

Wrong – This recessed light is not ICAT labeled.
Image:

Wrong – This seam along a common wall is not air sealed.

Wrong – This seam along a common wall is not air sealed.
Image:

Wrong – Top plate not air sealed

Wrong – Top plate not air sealed
Image:

Wrong – Top plate not air sealed

Wrong – Top plate not air sealed
Image:

Wrong – Top plate to drywall connection not sealed

Wrong – Top plate to drywall connection not sealed
Image:

Wrong – Top plate to drywall connection not sealed

Wrong – Top plate to drywall connection not sealed
Image:

Wrong – Top plate to drywall connection not sealed

Wrong – Top plate to drywall connection not sealed
Image:

Wrong – Vent sleeve not completely sealed

Wrong – Vent sleeve not completely sealed
Image:

Wrong – Wall from above without top plate or blocking installed

Wrong – Wall from above without top plate or blocking installed
Image:

Wrong – When insulating with spray foam, care should be taken to completely fill areas around piping and other penetrations to avoid leaving air gaps.

Wrong – When insulating with spray foam, care should be taken to completely fill areas around piping and other penetrations to avoid leaving air gaps.
Image:

Wrong – Where possible, design walls and specify window sizes and placement to minimize the use of studs around windows; and seal all wood-to-wood seams to minimize air leakage through walls.

Wrong – Where possible, design walls and specify window sizes and placement to minimize the use of studs around windows; and seal all wood-to-wood seams to minimize air leakage through walls.
Image:

Wrong – Whole house fan installed with holes in surrounding platform that need to be air sealed

Wrong – Whole house fan installed with holes in surrounding platform that need to be air sealed
Image:

Wrong – Whole house fan installed without an insulated cover

Wrong – Whole house fan installed without an insulated cover