Skip to main content

Resources

Explore a library of home construction and renovation guidance and easily search through galleries containing hundreds of building science-related photos, drawings, videos, CAD files, case studies, and presentations.

Filter

View Library

Showing 145 - 168 of 1611 results:

Image:

A flexible membrane was installed across the floor joists to prevent air movement between the floor joists in this multifamily 1-hr partition wall assembly

A flexible membrane was installed across the floor joists to prevent air movement between the floor joists in this multifamily 1-hr partition wall assembly
Image:

A home is tested at two points for enclosure air leakage

A home is tested at two points for enclosure air leakage
Image:

A large bead of caulk is installed on the interior surface of the wall top and bottom plates to provide an air sealing gasket between the framing and the dry wall.

A large bead of caulk is installed on the interior surface of the wall top and bottom plates to provide an air sealing gasket between the framing and the dry wall.
Image:

A low-sloped shed roof with the thermal boundary located at either a) the flat ceiling with a vented attic or b) the roof line for an unvented attic

A low-sloped shed roof with the thermal boundary located at either a) the flat ceiling with a vented attic or b) the roof line for an unvented attic
Image:

A manometer is used to measure pressure differentials between indoors and outdoors when testing whole-house air leakage.

A manometer is used to measure pressure differentials between indoors and outdoors when testing whole-house air leakage.
Image:

A monolithic concrete slab is insulated on the exterior slab edge with rigid foam

A monolithic concrete slab is insulated on the exterior slab edge with rigid foam
Image:

A piece of siding is used as sill extension and to provide slope in the opening for the window, which is deeper because exterior rigid foam has been added

A piece of siding is used as sill extension and to provide slope in the opening for the window, which is deeper because exterior rigid foam has been added
Image:

A pumper is used to place the concrete into the foam form walls

A pumper is used to place the concrete into the foam form walls
Image:

A putty knife is used to press caulk into a seam in the plywood sheathing.

A putty knife is used to press caulk into a seam in the plywood sheathing.
Image:

A rigid air barrier of non-paper-faced gypsum board is installed before the bathtub is installed and all seams are caulked

A rigid air barrier of non-paper-faced gypsum board is installed before the bathtub is installed and all seams are caulked
Image:

A second layer of rigid insulation is installed over the 2 in. by 4 in. retaining strip

A second layer of rigid insulation is installed over the 2 in. by 4 in. retaining strip
Image:

A sill gasket is installed under the two layers of fire-rated gypsum providing air sealing at the foundation slab in this 2-hour fire wall separating two units in a multifamily row house building

A sill gasket is installed under the two layers of fire-rated gypsum providing air sealing at the foundation slab in this 2-hour fire wall separating two units in a multifamily row house building
Image:

A sill-sealing foam gasket is placed under 8-inch plywood base and two beads of caulk air seal the 2x6 sill plate to it; two more beads of caulk will top the 2x6 which will serve as a spline for the SIP wall panel.

A sill-sealing foam gasket is placed under 8-inch plywood base and two beads of caulk air seal the 2x6 sill plate to it; two more beads of caulk will top the 2x6 which will serve as a spline for the SIP wall panel.
Image:

A site-built rafter roof with a raised top plate allows for more insulation underneath.

A site-built rafter roof with a raised top plate allows for more insulation underneath.
Image:

A standard site-built roof of rafters may pinch the insulation at the eaves

A standard site-built roof of rafters may pinch the insulation at the eaves
Image:

A structural spline made of a solid 2x is used where needed to meet structural load requirements at SIP panel seams

A structural spline made of a solid 2x is used where needed to meet structural load requirements at SIP panel seams
Image:

A surface spline reduces thermal bridging much more than a structural spline at SIP panel seams

A surface spline reduces thermal bridging much more than a structural spline at SIP panel seams
Image:

A technician assembles the spray sealant injection system to seal HVAC ducts from the inside

A technician assembles the spray sealant injection system to seal HVAC ducts from the inside
Image:

A technician conducts a duct blaster test

A technician conducts a duct blaster test
Image:

A weatherstripping gasket is installed on the framing that the crawlspace hatch panel rests on.

A weatherstripping gasket is installed on the framing that the crawlspace hatch panel rests on.
Image:

Adding air-sealing and rigid foam insulation at the wall-to-overhanging floor juncture at the outside corner of an existing home

Adding air-sealing and rigid foam insulation at the wall-to-overhanging floor juncture at the outside corner of an existing home
Video:

Adding weatherstripping to a door

Image:

Adhesive caulk is used to seal seams and attach the multiple layers of rigid insulation

Adhesive caulk is used to seal seams and attach the multiple layers of rigid insulation
Image:

Advanced framing details include corners that are constructed with fewer studs or studs aligned so that insulation can be installed in the corner.

Advanced framing details include corners that are constructed with fewer studs or studs aligned so that insulation can be installed in the corner.