Skip to main content

Resources

Explore a library of home construction and renovation guidance and easily search through galleries containing hundreds of building science-related photos, drawings, videos, CAD files, case studies, and presentations.

Filter

View Library

Showing 1825 - 1848 of 1860 results:

Image:

Wrong – There is not a water-resistant barrier installed underneath the exterior finish of the walls

Wrong – There is not a water-resistant barrier installed underneath the exterior finish of the walls
Image:

Wrong – These clay roof tiles were dislodged by high winds due to inadequate anchorage.

Wrong – These clay roof tiles were dislodged by high winds due to inadequate anchorage.
Image:

Wrong – These four ties were never embedded into the mortar joint, allowing the brick wall to be pulled away from the sheathing.

Wrong – These four ties were never embedded into the mortar joint, allowing the brick wall to be pulled away from the sheathing.
Image:

Wrong – This brick veneer failed in high winds (107 mph) because the ties pulled out of the substrate.

Wrong – This brick veneer failed in high winds (107 mph) because the ties pulled out of the substrate.
Image:

Wrong – This exhaust fan duct is wrong on several counts: it uses flex duct rather than smooth round metal duct as required by the IRC, the duct terminates inside of the wall assembly instead of outside, the opening is not large enough...

Wrong – This exhaust fan duct is wrong on several counts: it uses flex duct rather than smooth round metal duct as required by the IRC, the duct terminates inside of the wall assembly instead of outside, the opening is not large enough, and the end is crushed thus severely limiting air flow.
Image:

Wrong – This gable end wall failed because connectors were missing at points of support (blue circles) and the outlookers were not connected to the end truss (yellow circle)

Wrong – This gable end wall failed because connectors were missing at points of support (blue circles) and the outlookers were not connected to the end truss (yellow circle)
Image:

Wrong – This house under construction is lacking wall to truss bracing and the bottom chord of the scissor trusses is several feet above the top of the end wall top plate

Wrong – This house under construction is lacking wall to truss bracing and the bottom chord of the scissor trusses is several feet above the top of the end wall top plate
Image:

Wrong – This metal tie remained embedded in the mortar joint but the smooth-shank nail pulled out from the stud.

Wrong – This metal tie remained embedded in the mortar joint but the smooth-shank nail pulled out from the stud.
Image:

Wrong – This multi family building appears to be done in traditional southwest architecture but the lack of useful overhangs, dark colored walls, and lack of tinting on windows will result in significant solar heat gain.

Wrong – This multi family building appears to be done in traditional southwest architecture but the lack of useful overhangs, dark colored walls, and lack of tinting on windows will result in significant solar heat gain.
Image:

Wrong – This roof has no sheathing, when the metal panels blew off there was no secondary protection

Wrong – This roof has no sheathing, when the metal panels blew off there was no secondary protection
Image:

Wrong – This roof membrane on a low slope roof is fluttering and may fail because it is not fully adhered and deck seams below are not sealed, allowing air to leak up into the assembly while the membrane is pulled up due to negative pressures from wind

Wrong – This roof membrane on a low slope roof is fluttering and may fail because it is not fully adhered and deck seams below are not sealed, allowing air to leak up into the assembly while the membrane is pulled up due to negative pressures from wind
Image:

Wrong – This roof structure failed due to inadequate bracing

Wrong – This roof structure failed due to inadequate bracing
Image:

Wrong – This seam along a common wall is not air sealed.

Wrong – This seam along a common wall is not air sealed.
Image:

Wrong – This second-story floor plan has red lines that indicate openings from the attic into the interstitial floor space

Wrong – This second-story floor plan has red lines that indicate openings from the attic into the interstitial floor space
Image:

Wrong – Top plate not air sealed

Wrong – Top plate not air sealed
Image:

Wrong – Top plate not air sealed

Wrong – Top plate not air sealed
Image:

Wrong – Top plate to drywall connection not sealed

Wrong – Top plate to drywall connection not sealed
Image:

Wrong – Top plate to drywall connection not sealed

Wrong – Top plate to drywall connection not sealed
Image:

Wrong – Top plate to drywall connection not sealed

Wrong – Top plate to drywall connection not sealed
Image:

Wrong – Walls studs were cut too short, then not shimmed.

Wrong – Walls studs were cut too short, then not shimmed.
Image:

Wrong – When insulated sheathing is installed correctly, you should not see daylight. Nail holes were also left unplugged.

Wrong – When insulated sheathing is installed correctly, you should not see daylight. Nail holes were also left unplugged.
Image:

Wrong – Wind-driven rain and wildfire embers can enter an attic through the soffit vents.

Wrong – Wind-driven rain and wildfire embers can enter an attic through the soffit vents.
Image:

Wrong – Window has additional non-structural king stud

Wrong – Window has additional non-structural king stud
Image:

Wrong--No insulation installed behind fireplace

Wrong--No insulation installed behind fireplace