Skip to main content

Resources

Explore a library of home construction and renovation guidance and easily search through galleries containing hundreds of building science-related photos, drawings, videos, CAD files, case studies, and presentations.

Filter

View Library

Showing 769 - 790 of 790 results:

Image:

Wrong – Roof underlayment is not fully adhered and roof deck seams are not sealed so roof is susceptible to high-wind events

Wrong – Roof underlayment is not fully adhered and roof deck seams are not sealed so roof is susceptible to high-wind events
Image:

Wrong – The asphalt shingle shim is too small and the floor joist was cut too short.

Wrong – The asphalt shingle shim is too small and the floor joist was cut too short.
Image:

Wrong – The clips holding these metal roofing panels were set too far from the roof eave (above red line) and the panels lifted in strong winds

Wrong – The clips holding these metal roofing panels were set too far from the roof eave (above red line) and the panels lifted in strong winds
Image:

Wrong – The downspout terminates too close to the foundation of the house

Wrong – The downspout terminates too close to the foundation of the house
Image:

Wrong – The flashing of the roof-wall juncture was installed above the roof shingles instead of below the roof shingles; also no kickout flashing was installed.

Wrong – The flashing of the roof-wall juncture was installed above the roof shingles instead of below the roof shingles; also no kickout flashing was installed.
Image:

Wrong – The metal panels covering this roof used snaplocks and concealed fasteners that gave way in high winds.

Wrong – The metal panels covering this roof used snaplocks and concealed fasteners that gave way in high winds.
Image:

Wrong – The metal shingles and battens were inadequately secured

Wrong – The metal shingles and battens were inadequately secured
Image:

Wrong – The off-ridge roof vent on the right was poorly anchored and pulled off in high winds allowing water into the home.

Wrong – The off-ridge roof vent on the right was poorly anchored and pulled off in high winds allowing water into the home.
Image:

Wrong – The open overhang with exposed timbers and unscreened vent holes make this roof more susceptible to ignition.

Wrong – The open overhang with exposed timbers and unscreened vent holes make this roof more susceptible to ignition.
Image:

Wrong – The ridge flashing fasteners were placed too far apart and came loose in high winds.

Wrong – The ridge flashing fasteners were placed too far apart and came loose in high winds.
Image:

Wrong – The ridge flashing fasteners were placed too far apart and did not adequately hold the flashing in place

Wrong – The ridge flashing fasteners were placed too far apart and did not adequately hold the flashing in place
Image:

Wrong – The step flashing is not the required height above the roof deck

Wrong – The step flashing is not the required height above the roof deck
Image:

Wrong – the water-resistant barrier is layered underneath the step flashing, which could allow water to get behind the step flashing and into the wall.

Wrong – the water-resistant barrier is layered underneath the step flashing, which could allow water to get behind the step flashing and into the wall.
Image:

Wrong – There are no gutters installed and there is not a proper gravel bed located at the foundation

Wrong – There are no gutters installed and there is not a proper gravel bed located at the foundation
Image:

Wrong – There is not a self-sealing bituminous membrane installed at the valley of the roof

Wrong – There is not a self-sealing bituminous membrane installed at the valley of the roof
Image:

Wrong – These clay roof tiles were dislodged by high winds due to inadequate anchorage.

Wrong – These clay roof tiles were dislodged by high winds due to inadequate anchorage.
Image:

Wrong – This house under construction is lacking wall to truss bracing and the bottom chord of the scissor trusses is several feet above the top of the end wall top plate

Wrong – This house under construction is lacking wall to truss bracing and the bottom chord of the scissor trusses is several feet above the top of the end wall top plate
Image:

Wrong – This roof has no sheathing, when the metal panels blew off there was no secondary protection

Wrong – This roof has no sheathing, when the metal panels blew off there was no secondary protection
Image:

Wrong – This roof membrane on a low slope roof is fluttering and may fail because it is not fully adhered and deck seams below are not sealed, allowing air to leak up into the assembly while the membrane is pulled up due to negative pressures from wind

Wrong – This roof membrane on a low slope roof is fluttering and may fail because it is not fully adhered and deck seams below are not sealed, allowing air to leak up into the assembly while the membrane is pulled up due to negative pressures from wind
Image:

Wrong – Wind-driven rain and wildfire embers can enter an attic through the soffit vents.

Wrong – Wind-driven rain and wildfire embers can enter an attic through the soffit vents.
Image:

Wrong: Closed-cell spray foam roof insulation was not thick enough to meet IRC levels so the foam surface is colder than the dew point of the interior air and condensation formed on surface of the foam

Wrong: Closed-cell spray foam roof insulation was not thick enough to meet IRC levels so the foam surface is colder than the dew point of the interior air and condensation formed on surface of the foam
Video:

Your Home Can Survive a Wildfire