Skip to main content

Resources

Explore a library of home construction and renovation guidance and easily search through galleries containing hundreds of building science-related photos, drawings, videos, CAD files, case studies, and presentations.

Filter

View Library

Showing 673 - 690 of 690 results:

Image:

Wrong – The water-resistant barrier is not complete and the holes and gaps could cause moisture problems

Wrong – The water-resistant barrier is not complete and the holes and gaps could cause moisture problems
Image:

Wrong – There is not a water-resistant barrier installed underneath the exterior finish of the walls

Wrong – There is not a water-resistant barrier installed underneath the exterior finish of the walls
Image:

Wrong – There is visible light around the door because no weather stripping has been installed.

Wrong – There is visible light around the door because no weather stripping has been installed.
Image:

Wrong – These clay roof tiles were dislodged by high winds due to inadequate anchorage.

Wrong – These clay roof tiles were dislodged by high winds due to inadequate anchorage.
Image:

Wrong – These four ties were never embedded into the mortar joint, allowing the brick wall to be pulled away from the sheathing.

Wrong – These four ties were never embedded into the mortar joint, allowing the brick wall to be pulled away from the sheathing.
Image:

Wrong – This brick veneer failed in high winds (107 mph) because the ties pulled out of the substrate.

Wrong – This brick veneer failed in high winds (107 mph) because the ties pulled out of the substrate.
Image:

Wrong – This exhaust fan duct is wrong on several counts: it uses flex duct rather than smooth round metal duct as required by the IRC, the duct terminates inside of the wall assembly instead of outside, the opening is not large enough...

Wrong – This exhaust fan duct is wrong on several counts: it uses flex duct rather than smooth round metal duct as required by the IRC, the duct terminates inside of the wall assembly instead of outside, the opening is not large enough, and the end is crushed thus severely limiting air flow.
Image:

Wrong – This gable end wall failed because connectors were missing at points of support (blue circles) and the outlookers were not connected to the end truss (yellow circle)

Wrong – This gable end wall failed because connectors were missing at points of support (blue circles) and the outlookers were not connected to the end truss (yellow circle)
Image:

Wrong – This house was built on a shallow foundation instead of piers; the foundation was undermined by erosion from Hurricane Irma (Vilano Beach, FL)

Wrong – This house was built on a shallow foundation instead of piers; the foundation was undermined by erosion from Hurricane Irma (Vilano Beach, FL)
Image:

Wrong – This kitchen exhaust fan is not located directly above the stove top so it will be ineffective at removing cooking pollutants and it terminates within 3 feet of an operable window, which is prohibited by code.

Wrong – This kitchen exhaust fan is not located directly above the stove top so it will be ineffective at removing cooking pollutants and it terminates within 3 feet of an operable window, which is prohibited by code.
Image:

Wrong – This kitchen exhaust is a recirculating model; kitchens should use exhaust fans that duct out through the roof to remove moisture and odors from the home

Wrong – This kitchen exhaust is a recirculating model; kitchens should use exhaust fans that duct out through the roof to remove moisture and odors from the home
Image:

Wrong – This metal tie remained embedded in the mortar joint but the smooth-shank nail pulled out from the stud.

Wrong – This metal tie remained embedded in the mortar joint but the smooth-shank nail pulled out from the stud.
Image:

Wrong – This roof has no sheathing, when the metal panels blew off there was no secondary protection

Wrong – This roof has no sheathing, when the metal panels blew off there was no secondary protection
Image:

Wrong – This roof membrane on a low slope roof is fluttering and may fail because it is not fully adhered and deck seams below are not sealed, allowing air to leak up into the assembly while the membrane is pulled up due to negative pressures from wind

Wrong – This roof membrane on a low slope roof is fluttering and may fail because it is not fully adhered and deck seams below are not sealed, allowing air to leak up into the assembly while the membrane is pulled up due to negative pressures from wind
Image:

Wrong – Window not protected and failed due to windborne debris in hurricane force winds.

Wrong – Window not protected and failed due to windborne debris in hurricane force winds.
Image:

Wrong-The home was pulled off its masonry pier foundation during a coastal flood due to inadequate pier-to-beam connections.

Wrong-The home was pulled off its masonry pier foundation during a coastal flood due to inadequate pier-to-beam connections.
Image:

Wrong-These masonry pier foundations were twisted and displaced by coastal storm surges in Long Beach, Mississippi.

Wrong-These masonry pier foundations were twisted and displaced by coastal storm surges in Long Beach, Mississippi.
Image:

Wrong: The fiber-cement siding has cracked due to over-driven nails located too close to the edge of the board; these cracks provide a pathway for bulk water entry and offer little resistance to high winds.

Wrong: The fiber-cement siding has cracked due to over-driven nails located too close to the edge of the board; these cracks provide a pathway for bulk water entry and offer little resistance to high winds.