Skip to main content

Resources

Explore a library of home construction and renovation guidance and easily search through galleries containing hundreds of building science-related photos, drawings, videos, CAD files, case studies, and presentations.

Filter

View Library

Showing 1969 - 1992 of 2003 results:

Image:

Wrong – The vinyl siding at this gable was installed over rigid foam instead of wood sheathing and neither had the structural strength to resist hurricane wind pressures.

Wrong – The vinyl siding at this gable was installed over rigid foam instead of wood sheathing and neither had the structural strength to resist hurricane wind pressures.
Image:

Wrong – The vinyl siding was not properly locked into the panel below.

Wrong – The vinyl siding was not properly locked into the panel below.
Image:

Wrong – the water-resistant barrier is layered underneath the step flashing, which could allow water to get behind the step flashing and into the wall.

Wrong – the water-resistant barrier is layered underneath the step flashing, which could allow water to get behind the step flashing and into the wall.
Image:

Wrong – The water-resistant barrier is not complete and the holes and gaps could cause moisture problems

Wrong – The water-resistant barrier is not complete and the holes and gaps could cause moisture problems
Image:

Wrong – There are no gutters installed and there is not a proper gravel bed located at the foundation

Wrong – There are no gutters installed and there is not a proper gravel bed located at the foundation
Image:

Wrong – There is carpet installed too close to the plumbing fixtures in the bathroom

Wrong – There is carpet installed too close to the plumbing fixtures in the bathroom
Image:

Wrong – There is carpet installed too close to the plumbing fixtures in the bathroom

Wrong – There is carpet installed too close to the plumbing fixtures in the bathroom
Image:

Wrong – There is no backing installed behind the shower enclosure.

Wrong – There is no backing installed behind the shower enclosure.
Image:

Wrong – There is no flashing installed along the sides of the window

Wrong – There is no flashing installed along the sides of the window
Image:

Wrong – There is no flashing installed at the bottom of the exterior walls to create a drainage system

Wrong – There is no flashing installed at the bottom of the exterior walls to create a drainage system
Image:

Wrong – There is no flashing installed at the bottom of the exterior walls to create a drainage system

Wrong – There is no flashing installed at the bottom of the exterior walls to create a drainage system
Image:

Wrong – There is no flashing installed at the top of the window

Wrong – There is no flashing installed at the top of the window
Image:

Wrong – There is no weather stripping or gasket around the attic stair hatch

Wrong – There is no weather stripping or gasket around the attic stair hatch
Image:

Wrong – There is not a self-sealing bituminous membrane installed at the valley of the roof

Wrong – There is not a self-sealing bituminous membrane installed at the valley of the roof
Image:

Wrong – There is not a water-resistant barrier installed underneath the exterior finish of the walls

Wrong – There is not a water-resistant barrier installed underneath the exterior finish of the walls
Image:

Wrong – These four ties were never embedded into the mortar joint, allowing the brick wall to be pulled away from the sheathing.

Wrong – These four ties were never embedded into the mortar joint, allowing the brick wall to be pulled away from the sheathing.
Image:

Wrong – This brick veneer failed in high winds (107 mph) because the ties pulled out of the substrate.

Wrong – This brick veneer failed in high winds (107 mph) because the ties pulled out of the substrate.
Image:

Wrong – This metal tie remained embedded in the mortar joint but the smooth-shank nail pulled out from the stud.

Wrong – This metal tie remained embedded in the mortar joint but the smooth-shank nail pulled out from the stud.
Image:

Wrong – This roof has no sheathing, when the metal panels blew off there was no secondary protection

Wrong – This roof has no sheathing, when the metal panels blew off there was no secondary protection
Image:

Wrong – This vented crawlspace has standing water because steps were not taken to address site conditions that led to bulk water flow into the crawlspace

Wrong – This vented crawlspace has standing water because steps were not taken to address site conditions that led to bulk water flow into the crawlspace
Image:

Wrong – When insulated sheathing is installed correctly, you should not see daylight. Nail holes were also left unplugged.

Wrong – When insulated sheathing is installed correctly, you should not see daylight. Nail holes were also left unplugged.
Image:

Wrong – When insulating with spray foam, care should be taken to completely fill areas around piping and other penetrations to avoid leaving air gaps.

Wrong – When insulating with spray foam, care should be taken to completely fill areas around piping and other penetrations to avoid leaving air gaps.
Image:

Wrong – When more than one layer of insulation is installed, the seams should be staggered to discourage ground water from reaching the foundation wall.

Wrong – When more than one layer of insulation is installed, the seams should be staggered to discourage ground water from reaching the foundation wall.
Image:

Wrong- A tie strap should not be used over the duct outer liner because it can compress the insulation. Tuck in the fibrous insulation and seal the outer liner to the connecting duct with mastic or foil tape (Steven Winter Associates 2013).

Wrong- A tie strap should not be used over the duct outer liner because it can compress the insulation. Tuck in the fibrous insulation and seal the outer liner to the connecting duct with mastic or foil tape (Steven Winter Associates 2013).