Skip to main content

Resources

Explore a library of home construction and renovation guidance and easily search through galleries containing hundreds of building science-related photos, drawings, videos, CAD files, case studies, and presentations.

Filter

View Library

Showing 1393 - 1414 of 1414 results:

Image:

Wrong – The batt insulation on this knee wall is not properly supported and there is no air sealed rigid backing to provide a solid air barrier.

Wrong – The batt insulation on this knee wall is not properly supported and there is no air sealed rigid backing to provide a solid air barrier.
Image:

Wrong – The framing and wind baffle installation will not allow for required insulation depth.

Wrong – The framing and wind baffle installation will not allow for required insulation depth.
Image:

Wrong – The framing will not allow for required insulation depth.

Wrong – The framing will not allow for required insulation depth.
Image:

Wrong – The gable end wall failed because the rigid foam sheathing was not backed up by plywood or OSB.

Wrong – The gable end wall failed because the rigid foam sheathing was not backed up by plywood or OSB.
Image:

Wrong – The polyethylene sheeting vapor barrier is not attached to the piers with mechanical fasteners

Wrong – The polyethylene sheeting vapor barrier is not attached to the piers with mechanical fasteners
Image:

Wrong – The stud was cut too long then not installed plumb and level.

Wrong – The stud was cut too long then not installed plumb and level.
Image:

Wrong – There is no weather stripping or gasket around the attic stair hatch

Wrong – There is no weather stripping or gasket around the attic stair hatch
Image:

Wrong – When insulated sheathing is installed correctly, you should not see daylight. Nail holes were also left unplugged.

Wrong – When insulated sheathing is installed correctly, you should not see daylight. Nail holes were also left unplugged.
Image:

Wrong – When insulating with spray foam, care should be taken to completely fill areas around piping and other penetrations to avoid leaving air gaps.

Wrong – When insulating with spray foam, care should be taken to completely fill areas around piping and other penetrations to avoid leaving air gaps.
Image:

Wrong – When more than one layer of insulation is installed, the seams should be staggered to discourage ground water from reaching the foundation wall.

Wrong – When more than one layer of insulation is installed, the seams should be staggered to discourage ground water from reaching the foundation wall.
Image:

Wrong- A tie strap should not be used over the duct outer liner because it can compress the insulation. Tuck in the fibrous insulation and seal the outer liner to the connecting duct with mastic or foil tape (Steven Winter Associates 2013).

Wrong- A tie strap should not be used over the duct outer liner because it can compress the insulation. Tuck in the fibrous insulation and seal the outer liner to the connecting duct with mastic or foil tape (Steven Winter Associates 2013).
Image:

Wrong: Closed-cell spray foam roof insulation was not thick enough to meet IRC levels so the foam surface is colder than the dew point of the interior air and condensation formed on surface of the foam

Wrong: Closed-cell spray foam roof insulation was not thick enough to meet IRC levels so the foam surface is colder than the dew point of the interior air and condensation formed on surface of the foam
Image:

Wrong: Duct is hung between truss members by strapping and not buried

Wrong: Duct is hung between truss members by strapping and not buried
Image:

Wrong: Ducts are held above the ceiling plane with strapping to provide a good angle into top-entry boots. Once the ceiling insulation is added, this duct will protrude from the ceiling insulation and will not be buried

Wrong: Ducts are held above the ceiling plane with strapping to provide a good angle into top-entry boots. Once the ceiling insulation is added, this duct will protrude from the ceiling insulation and will not be buried
Image:

Wrong: Ducts are held from the rafters with strapping and a large beam prevents ducts from properly lying on the ceiling plane

Wrong: Ducts are held from the rafters with strapping and a large beam prevents ducts from properly lying on the ceiling plane
Image:

Wrong: Ducts are not laid across the lower truss cords or ceiling, but are hung from the rafters by straps. As a result, ductwork is not buried

Wrong: Ducts are not laid across the lower truss cords or ceiling, but are hung from the rafters by straps. As a result, ductwork is not buried
Image:

Wrong: Ductwork is not fully encapsulated with ccSPF insulation. The duct jacket is still fully visible at sections of the duct

Wrong: Ductwork is not fully encapsulated with ccSPF insulation. The duct jacket is still fully visible at sections of the duct
Image:

Wrong: Insulation not fully enclosing duct chase

Wrong: Insulation not fully enclosing duct chase
Image:

Wrong: This exhaust fan duct is too long and terminates in the attic instead of going through the roof and it is improperly supported; it needs straps all along its length to prevent sagging.

Wrong: This exhaust fan duct is too long and terminates in the attic instead of going through the roof and it is improperly supported; it needs straps all along its length to prevent sagging.
Video:

Your Northern Home: Understanding Crawl Spaces

Video:

Your Northern Home: Walls

Image:

Zero Net Now built this custom for buyer home in the cold climate in New Paltz, NY, and certified it to DOE Zero Energy Ready Home specifications in 2021.

Zero Net Now built this custom for buyer home in the cold climate in New Paltz, NY, and certified it to DOE Zero Energy Ready Home specifications in 2021.