Skip to main content

Resources

Explore a library of home construction and renovation guidance and easily search through galleries containing hundreds of building science-related photos, drawings, videos, CAD files, case studies, and presentations.

Filter

View Library

Showing 1009 - 1031 of 1031 results:

Image:

Wrong – Rigid insulation is being installed without cap nails

Wrong – Rigid insulation is being installed without cap nails
Image:

Wrong – Slab insulation does not extend to the top of the slab

Wrong – Slab insulation does not extend to the top of the slab
Image:

Wrong – Slab insulation does not extend to the top of the slab

Wrong – Slab insulation does not extend to the top of the slab
Image:

Wrong – The framing and wind baffle installation will not allow for required insulation depth.

Wrong – The framing and wind baffle installation will not allow for required insulation depth.
Image:

Wrong – The framing will not allow for required insulation depth.

Wrong – The framing will not allow for required insulation depth.
Image:

Wrong – The HVAC compressor was not adequately secured to an elevated platform and was washed away.

Wrong – The HVAC compressor was not adequately secured to an elevated platform and was washed away.
Image:

Wrong – These flex ducts are pulled taut, which is correct but they are inadequately supported with straps that are spaced too far apart and are too tight causing pinching of the insulation and turns are sharp rather than gradual.

Wrong – These flex ducts are pulled taut, which is correct but they are inadequately supported with straps that are spaced too far apart and are too tight causing pinching of the insulation and turns are sharp rather than gradual.
Image:

Wrong – This second-story floor plan has red lines that indicate openings from the attic into the interstitial floor space

Wrong – This second-story floor plan has red lines that indicate openings from the attic into the interstitial floor space
Image:

Wrong – Two combustion appliances are sharing a flue which could lead to backdrafting if one appliance is updated to a direct vent appliance and disconnected from shared chimney.

Wrong – Two combustion appliances are sharing a flue which could lead to backdrafting if one appliance is updated to a direct vent appliance and disconnected from shared chimney.
Image:

Wrong – When insulated sheathing is installed correctly, you should not see daylight. Nail holes were also left unplugged.

Wrong – When insulated sheathing is installed correctly, you should not see daylight. Nail holes were also left unplugged.
Image:

Wrong – Window has additional non-structural king stud

Wrong – Window has additional non-structural king stud
Image:

Wrong- A tie strap should not be used over the duct outer liner because it can compress the insulation. Tuck in the fibrous insulation and seal the outer liner to the connecting duct with mastic or foil tape (Steven Winter Associates 2013).

Wrong- A tie strap should not be used over the duct outer liner because it can compress the insulation. Tuck in the fibrous insulation and seal the outer liner to the connecting duct with mastic or foil tape (Steven Winter Associates 2013).
Image:

Wrong: Open wall cavities in the un-air-sealed return plenum connect the plenum to attic spaces

Wrong: Open wall cavities in the un-air-sealed return plenum connect the plenum to attic spaces
Image:

Wrong: open wall cavity connected to this return air plenum is allowing cellulose attic insulation to be pulled into the furnace

Wrong: open wall cavity connected to this return air plenum is allowing cellulose attic insulation to be pulled into the furnace
Image:

Wrong: Sized per Approach 1 or 2, this heat pump’s modulating zone has a small overlap with the home’s heating load line, resulting in a large amount of short-cycling; the unit will require backup heat when the temperature is below 25°F

Wrong: Sized per Approach 1 or 2, this heat pump’s modulating zone has a small overlap with the home’s heating load line, resulting in a large amount of short-cycling; the unit will require backup heat when the temperature is below 25°F
Image:

Wrong: Sized per Approach 3, there is minimal overlap between this heat pump’s modulating zone and the home’s heating load line, causing excessive short-cycling; it will require backup heat and may not contribute significantly at temperatures below 5°F

Wrong: Sized per Approach 3, there is minimal overlap between this heat pump’s modulating zone and the home’s heating load line, causing excessive short-cycling; it will require backup heat and may not contribute significantly at temperatures below 5°F
Image:

Wrong: Sized per Approach 3, there is small overlap between this heat pump’s modulating zone and the home’s heating load line, resulting in excessive short-cycling; it will require backup heat when the temperature is below 5°F

Wrong: Sized per Approach 3, there is small overlap between this heat pump’s modulating zone and the home’s heating load line, resulting in excessive short-cycling; it will require backup heat when the temperature is below 5°F
Image:

Wrong: The door and filter were removed, allowing unfiltered air to enter the air handler leading to premature failure of the system due to dirt accumulation.

Wrong: The door and filter were removed, allowing unfiltered air to enter the air handler leading to premature failure of the system due to dirt accumulation.
Image:

Wrong: The return plenum is not air sealed to separate it from the wall cavities and it should not be used for storage

Wrong: The return plenum is not air sealed to separate it from the wall cavities and it should not be used for storage
Image:

Wrong: This air handling equipment is installed in the garage without isolating the equipment from the garage space

Wrong: This air handling equipment is installed in the garage without isolating the equipment from the garage space
Image:

Wrong: This heat pump is oversized even for Approach 4, and its modulating zone has a small overlap with the home’s heating load line, resulting in a large amount of short-cycling.

Wrong: This heat pump is oversized even for Approach 4, and its modulating zone has a small overlap with the home’s heating load line, resulting in a large amount of short-cycling.
Image:

Wrong: This return air plenum is not lined and air sealed

Wrong: This return air plenum is not lined and air sealed
Image:

Wrong: This wall cavity is open to the attic allowing unconditioned, attic air to enter the HVAC system, bypassing the filter, and degrading system life and performance

Wrong: This wall cavity is open to the attic allowing unconditioned, attic air to enter the HVAC system, bypassing the filter, and degrading system life and performance