Skip to main content

Resources

Explore a library of home construction and renovation guidance and easily search through galleries containing hundreds of building science-related photos, drawings, videos, CAD files, case studies, and presentations.

Filter

View Library

Showing 961 - 980 of 980 results:

Image:

Wrong – The ridge flashing fasteners were placed too far apart and came loose in high winds.

Wrong – The ridge flashing fasteners were placed too far apart and came loose in high winds.
Image:

Wrong – The ridge flashing fasteners were placed too far apart and did not adequately hold the flashing in place

Wrong – The ridge flashing fasteners were placed too far apart and did not adequately hold the flashing in place
Image:

Wrong – The step flashing is not the required height above the roof deck

Wrong – The step flashing is not the required height above the roof deck
Image:

Wrong – the water-resistant barrier is layered underneath the step flashing, which could allow water to get behind the step flashing and into the wall.

Wrong – the water-resistant barrier is layered underneath the step flashing, which could allow water to get behind the step flashing and into the wall.
Image:

Wrong – There are no gutters installed and there is not a proper gravel bed located at the foundation

Wrong – There are no gutters installed and there is not a proper gravel bed located at the foundation
Image:

Wrong – There is not a self-sealing bituminous membrane installed at the valley of the roof

Wrong – There is not a self-sealing bituminous membrane installed at the valley of the roof
Image:

Wrong – These clay roof tiles were dislodged by high winds due to inadequate anchorage.

Wrong – These clay roof tiles were dislodged by high winds due to inadequate anchorage.
Image:

Wrong – This house under construction is lacking wall to truss bracing and the bottom chord of the scissor trusses is several feet above the top of the end wall top plate

Wrong – This house under construction is lacking wall to truss bracing and the bottom chord of the scissor trusses is several feet above the top of the end wall top plate
Image:

Wrong – This roof has no sheathing, when the metal panels blew off there was no secondary protection

Wrong – This roof has no sheathing, when the metal panels blew off there was no secondary protection
Image:

Wrong – This roof membrane on a low slope roof is fluttering and may fail because it is not fully adhered and deck seams below are not sealed, allowing air to leak up into the assembly while the membrane is pulled up due to negative pressures from wind

Wrong – This roof membrane on a low slope roof is fluttering and may fail because it is not fully adhered and deck seams below are not sealed, allowing air to leak up into the assembly while the membrane is pulled up due to negative pressures from wind
Image:

Wrong – Wind-driven rain and wildfire embers can enter an attic through the soffit vents.

Wrong – Wind-driven rain and wildfire embers can enter an attic through the soffit vents.
Image:

Wrong: Closed-cell spray foam roof insulation was not thick enough to meet IRC levels so the foam surface is colder than the dew point of the interior air and condensation formed on surface of the foam

Wrong: Closed-cell spray foam roof insulation was not thick enough to meet IRC levels so the foam surface is colder than the dew point of the interior air and condensation formed on surface of the foam
Image:

Wrong: HPWH inlet and outlet are piped to mixing valve inlet and DCW make up, driving erratic HPWH and mixing valve behavior

Wrong: HPWH inlet and outlet are piped to mixing valve inlet and DCW make up, driving erratic HPWH and mixing valve behavior
Image:

Wrong: Not enough space was left in the floorplans for both the heat pump water heater and a duct elbow to be attached to the right side of the water heater (the orange circle outlines the tank; the rectangle shows the space needed for the duct)

Wrong: Not enough space was left in the floorplans for both the heat pump water heater and a duct elbow to be attached to the right side of the water heater (the orange circle outlines the tank; the rectangle shows the space needed for the duct)
Image:

Wrong: Sized per Approach 1 or 2, this heat pump’s modulating zone has a small overlap with the home’s heating load line, resulting in a large amount of short-cycling; the unit will require backup heat when the temperature is below 25°F

Wrong: Sized per Approach 1 or 2, this heat pump’s modulating zone has a small overlap with the home’s heating load line, resulting in a large amount of short-cycling; the unit will require backup heat when the temperature is below 25°F
Image:

Wrong: Sized per Approach 3, there is minimal overlap between this heat pump’s modulating zone and the home’s heating load line, causing excessive short-cycling; it will require backup heat and may not contribute significantly at temperatures below 5°F

Wrong: Sized per Approach 3, there is minimal overlap between this heat pump’s modulating zone and the home’s heating load line, causing excessive short-cycling; it will require backup heat and may not contribute significantly at temperatures below 5°F
Image:

Wrong: Sized per Approach 3, there is small overlap between this heat pump’s modulating zone and the home’s heating load line, resulting in excessive short-cycling; it will require backup heat when the temperature is below 5°F

Wrong: Sized per Approach 3, there is small overlap between this heat pump’s modulating zone and the home’s heating load line, resulting in excessive short-cycling; it will require backup heat when the temperature is below 5°F
Image:

Wrong: The exhaust air from one heat pump water heater is blowing into the intake of the heat pump water heater next to it

Wrong: The exhaust air from one heat pump water heater is blowing into the intake of the heat pump water heater next to it
Image:

Wrong: This heat pump is oversized even for Approach 4, and its modulating zone has a small overlap with the home’s heating load line, resulting in a large amount of short-cycling.

Wrong: This heat pump is oversized even for Approach 4, and its modulating zone has a small overlap with the home’s heating load line, resulting in a large amount of short-cycling.
Video:

Your Home Can Survive a Wildfire