Skip to main content

Resources

Explore a library of home construction and renovation guidance and easily search through galleries containing hundreds of building science-related photos, drawings, videos, CAD files, case studies, and presentations.

Filter

View Library

Showing 865 - 888 of 908 results:

Image:

Wrong – Fibrous insulation does not air seal

Wrong – Fibrous insulation does not air seal
Image:

Wrong – Flex duct is coiled and looped

Wrong – Flex duct is coiled and looped
Image:

Wrong – Flex duct is pinched

Wrong – Flex duct is pinched
Image:

Wrong – Insulation should not be pinched where flex ducts connect to the trunk duct as compression of the insulation here can lead to cold spots and condensation on the duct surface.

Wrong – Insulation should not be pinched where flex ducts connect to the trunk duct as compression of the insulation here can lead to cold spots and condensation on the duct surface.
Image:

Wrong – It is difficult to test the air flow in this fresh air intake duct due to poor access and inadequate length of straight duct to get an accurate in-line flow measurement.

Wrong – It is difficult to test the air flow in this fresh air intake duct due to poor access and inadequate length of straight duct to get an accurate in-line flow measurement.
Image:

Wrong – Penetration hole is larger than duct and not sealed

Wrong – Penetration hole is larger than duct and not sealed
Image:

Wrong – The damper leading to the ductwork for a central ERV is closed during a duct leakage test; the duct tester is attached to the ERV cabinet, so this will only measure the air tightness of the ERV cabinet and not the duct system

Wrong – The damper leading to the ductwork for a central ERV is closed during a duct leakage test; the duct tester is attached to the ERV cabinet, so this will only measure the air tightness of the ERV cabinet and not the duct system
Image:

Wrong – The duct for this kitchen exhaust fan is made of flex duct instead of smooth metal duct and the duct is not properly supported.

Wrong – The duct for this kitchen exhaust fan is made of flex duct instead of smooth metal duct and the duct is not properly supported.
Image:

Wrong – the exhaust terminal for a clothes dryer should not be covered with a screen which could trap lint; instead, cover it with a hooded, louvered damper

Wrong – the exhaust terminal for a clothes dryer should not be covered with a screen which could trap lint; instead, cover it with a hooded, louvered damper
Image:

Wrong – The gas water heater is left on during enclosure leakage testing, which could result in dangerous backdrafting of the water heater when the home is depressurized

Wrong – The gas water heater is left on during enclosure leakage testing, which could result in dangerous backdrafting of the water heater when the home is depressurized
Image:

Wrong – the interior seam of the branch duct to trunk duct juncture is sealed with mastic but there are gaps around the exterior seam that should also be sealed with mastic or metal tape.

Wrong – the interior seam of the branch duct to trunk duct juncture is sealed with mastic but there are gaps around the exterior seam that should also be sealed with mastic or metal tape.
Image:

Wrong – The kitchen exhaust fan duct is attached to flex duct, which is prohibited by code.

Wrong – The kitchen exhaust fan duct is attached to flex duct, which is prohibited by code.
Image:

Wrong – The plastic seal of the open end of this duct is ripped; the test measurement will overestimate the duct leakage if the temporary seals are not very carefully completed

Wrong – The plastic seal of the open end of this duct is ripped; the test measurement will overestimate the duct leakage if the temporary seals are not very carefully completed
Image:

Wrong – These flex ducts are pulled taut, which is correct but they are inadequately supported with straps that are spaced too far apart and are too tight causing pinching of the insulation and turns are sharp rather than gradual.

Wrong – These flex ducts are pulled taut, which is correct but they are inadequately supported with straps that are spaced too far apart and are too tight causing pinching of the insulation and turns are sharp rather than gradual.
Image:

Wrong – This damper is closed, so the duct system is not entirely pressurized during the duct leakage test

Wrong – This damper is closed, so the duct system is not entirely pressurized during the duct leakage test
Image:

Wrong – This duct boot is not sealed to the wall board

Wrong – This duct boot is not sealed to the wall board
Image:

Wrong – This duct boot is sealed inside the boot for a duct leakage test; this fails to account for the ductwork leakage between the duct boot and the wall board

Wrong – This duct boot is sealed inside the boot for a duct leakage test; this fails to account for the ductwork leakage between the duct boot and the wall board
Image:

Wrong – This ductwork is not sealed where the round duct is attached to the square duct riser

Wrong – This ductwork is not sealed where the round duct is attached to the square duct riser
Image:

Wrong – This exhaust fan duct is wrong on several counts: it uses flex duct rather than smooth round metal duct as required by the IRC, the duct terminates inside of the wall assembly instead of outside, the opening is not large enough...

Wrong – This exhaust fan duct is wrong on several counts: it uses flex duct rather than smooth round metal duct as required by the IRC, the duct terminates inside of the wall assembly instead of outside, the opening is not large enough, and the end is crushed thus severely limiting air flow.
Image:

Wrong – This fire damper is partly closed during a duct leakage test, resulting in an uneven pressure distribution and an inaccurate test result

Wrong – This fire damper is partly closed during a duct leakage test, resulting in an uneven pressure distribution and an inaccurate test result
Image:

Wrong – This metal duct is crushed, is sealed with duct tape instead of mastic or UL-181 metal tape, and is not correctly supported.

Wrong – This metal duct is crushed, is sealed with duct tape instead of mastic or UL-181 metal tape, and is not correctly supported.
Image:

Wrong – This water heater was not braced; it fell during an earthquake and ruptured the gas line causing a house fire.

Wrong – This water heater was not braced; it fell during an earthquake and ruptured the gas line causing a house fire.
Image:

Wrong – Two combustion appliances are sharing a flue which could lead to backdrafting if one appliance is updated to a direct vent appliance and disconnected from shared chimney.

Wrong – Two combustion appliances are sharing a flue which could lead to backdrafting if one appliance is updated to a direct vent appliance and disconnected from shared chimney.
Image:

Wrong – Vent sleeve not completely sealed

Wrong – Vent sleeve not completely sealed