Skip to main content

Resources

Explore a library of home construction and renovation guidance and easily search through galleries containing hundreds of building science-related photos, drawings, videos, CAD files, case studies, and presentations.

Filter

View Library

Showing 1921 - 1944 of 1970 results:

Image:

Wrong – There is not a self-sealing bituminous membrane installed at the valley of the roof

Wrong – There is not a self-sealing bituminous membrane installed at the valley of the roof
Image:

Wrong – There is not a water-resistant barrier installed underneath the exterior finish of the walls

Wrong – There is not a water-resistant barrier installed underneath the exterior finish of the walls
Image:

Wrong – These flex ducts are pulled taut, which is correct but they are inadequately supported with straps that are spaced too far apart and are too tight causing pinching of the insulation and turns are sharp rather than gradual.

Wrong – These flex ducts are pulled taut, which is correct but they are inadequately supported with straps that are spaced too far apart and are too tight causing pinching of the insulation and turns are sharp rather than gradual.
Image:

Wrong – These four ties were never embedded into the mortar joint, allowing the brick wall to be pulled away from the sheathing.

Wrong – These four ties were never embedded into the mortar joint, allowing the brick wall to be pulled away from the sheathing.
Image:

Wrong – This brick veneer failed in high winds (107 mph) because the ties pulled out of the substrate.

Wrong – This brick veneer failed in high winds (107 mph) because the ties pulled out of the substrate.
Image:

Wrong – This damper is closed, so the duct system is not entirely pressurized during the duct leakage test

Wrong – This damper is closed, so the duct system is not entirely pressurized during the duct leakage test
Image:

Wrong – This duct boot is not sealed to the wall board

Wrong – This duct boot is not sealed to the wall board
Image:

Wrong – This duct boot is sealed inside the boot for a duct leakage test; this fails to account for the ductwork leakage between the duct boot and the wall board

Wrong – This duct boot is sealed inside the boot for a duct leakage test; this fails to account for the ductwork leakage between the duct boot and the wall board
Image:

Wrong – This ductwork is not sealed where the round duct is attached to the square duct riser

Wrong – This ductwork is not sealed where the round duct is attached to the square duct riser
Image:

Wrong – This exhaust fan duct is wrong on several counts: it uses flex duct rather than smooth round metal duct as required by the IRC, the duct terminates inside of the wall assembly instead of outside, the opening is not large enough...

Wrong – This exhaust fan duct is wrong on several counts: it uses flex duct rather than smooth round metal duct as required by the IRC, the duct terminates inside of the wall assembly instead of outside, the opening is not large enough, and the end is crushed thus severely limiting air flow.
Image:

Wrong – This fire damper is partly closed during a duct leakage test, resulting in an uneven pressure distribution and an inaccurate test result

Wrong – This fire damper is partly closed during a duct leakage test, resulting in an uneven pressure distribution and an inaccurate test result
Image:

Wrong – This gable end wall failed because connectors were missing at points of support (blue circles) and the outlookers were not connected to the end truss (yellow circle)

Wrong – This gable end wall failed because connectors were missing at points of support (blue circles) and the outlookers were not connected to the end truss (yellow circle)
Image:

Wrong – This house under construction is lacking wall to truss bracing and the bottom chord of the scissor trusses is several feet above the top of the end wall top plate

Wrong – This house under construction is lacking wall to truss bracing and the bottom chord of the scissor trusses is several feet above the top of the end wall top plate
Image:

Wrong – This metal duct is crushed, is sealed with duct tape instead of mastic or UL-181 metal tape, and is not correctly supported.

Wrong – This metal duct is crushed, is sealed with duct tape instead of mastic or UL-181 metal tape, and is not correctly supported.
Image:

Wrong – This metal tie remained embedded in the mortar joint but the smooth-shank nail pulled out from the stud.

Wrong – This metal tie remained embedded in the mortar joint but the smooth-shank nail pulled out from the stud.
Image:

Wrong – This multi family building appears to be done in traditional southwest architecture but the lack of useful overhangs, dark colored walls, and lack of tinting on windows will result in significant solar heat gain.

Wrong – This multi family building appears to be done in traditional southwest architecture but the lack of useful overhangs, dark colored walls, and lack of tinting on windows will result in significant solar heat gain.
Image:

Wrong – This roof structure failed due to inadequate bracing

Wrong – This roof structure failed due to inadequate bracing
Image:

Wrong – This seam along a common wall is not air sealed.

Wrong – This seam along a common wall is not air sealed.
Image:

Wrong – This second-story floor plan has red lines that indicate openings from the attic into the interstitial floor space

Wrong – This second-story floor plan has red lines that indicate openings from the attic into the interstitial floor space
Image:

Wrong – Top plate not air sealed

Wrong – Top plate not air sealed
Image:

Wrong – Top plate not air sealed

Wrong – Top plate not air sealed
Image:

Wrong – Top plate to drywall connection not sealed

Wrong – Top plate to drywall connection not sealed
Image:

Wrong – Top plate to drywall connection not sealed

Wrong – Top plate to drywall connection not sealed
Image:

Wrong – Top plate to drywall connection not sealed

Wrong – Top plate to drywall connection not sealed