Skip to main content

Resources

Explore a library of home construction and renovation guidance and easily search through galleries containing hundreds of building science-related photos, drawings, videos, CAD files, case studies, and presentations.

Filter

View Library

Showing 697 - 720 of 751 results:

Image:

Wrong -The duct does not have enough support so it is sagging and compressing the duct

Wrong -The duct does not have enough support so it is sagging and compressing the duct
Image:

Wrong – A tear in the outer jacket of this duct shows where an in-line airflow measurement was made; the inner duct was not sealed and created a duct leak.

Wrong – A tear in the outer jacket of this duct shows where an in-line airflow measurement was made; the inner duct was not sealed and created a duct leak.
Image:

Wrong – Air sealing and fastening of this duct take-off has been damaged during construction, causing a large gap in the right-hand side of the connection that will reduce air delivered to living spaces and make it difficult to balance the system

Wrong – Air sealing and fastening of this duct take-off has been damaged during construction, causing a large gap in the right-hand side of the connection that will reduce air delivered to living spaces and make it difficult to balance the system
Image:

Wrong – Chase not capped

Wrong – Chase not capped
Image:

Wrong – Don’t use nails to fasten poly vapor barrier around flex ducts; it will allow moist air to reach the ducts where it could condense and ruin the insulation.

Wrong – Don’t use nails to fasten poly vapor barrier around flex ducts; it will allow moist air to reach the ducts where it could condense and ruin the insulation.
Image:

Wrong – Duct is pulling away from ceiling because it is not sealed to the ceiling

Wrong – Duct is pulling away from ceiling because it is not sealed to the ceiling
Image:

Wrong – Duct is pulling away from floor because it is not sealed to floor

Wrong – Duct is pulling away from floor because it is not sealed to floor
Image:

Wrong – Excessive bends in flex ducts

Wrong – Excessive bends in flex ducts
Image:

Wrong – Exhaust fan ducts must be smooth metal ducts; flex duct is not permitted by the IRC.

Wrong – Exhaust fan ducts must be smooth metal ducts; flex duct is not permitted by the IRC.
Image:

Wrong – Fiber board duct is not sealed at seams; flex duct is sealed with duct tape not mastic tape or UL-181 metal tape.

Wrong – Fiber board duct is not sealed at seams; flex duct is sealed with duct tape not mastic tape or UL-181 metal tape.
Image:

Wrong – Fibrous insulation does not air seal

Wrong – Fibrous insulation does not air seal
Image:

Wrong – Flex duct is coiled and looped

Wrong – Flex duct is coiled and looped
Image:

Wrong – Flex duct is pinched

Wrong – Flex duct is pinched
Image:

Wrong – Insulation should not be pinched where flex ducts connect to the trunk duct as compression of the insulation here can lead to cold spots and condensation on the duct surface.

Wrong – Insulation should not be pinched where flex ducts connect to the trunk duct as compression of the insulation here can lead to cold spots and condensation on the duct surface.
Image:

Wrong – It is difficult to test the air flow in this fresh air intake duct due to poor access and inadequate length of straight duct to get an accurate in-line flow measurement.

Wrong – It is difficult to test the air flow in this fresh air intake duct due to poor access and inadequate length of straight duct to get an accurate in-line flow measurement.
Image:

Wrong – Penetration hole is larger than duct and not sealed

Wrong – Penetration hole is larger than duct and not sealed
Image:

Wrong – The damper leading to the ductwork for a central ERV is closed during a duct leakage test; the duct tester is attached to the ERV cabinet, so this will only measure the air tightness of the ERV cabinet and not the duct system

Wrong – The damper leading to the ductwork for a central ERV is closed during a duct leakage test; the duct tester is attached to the ERV cabinet, so this will only measure the air tightness of the ERV cabinet and not the duct system
Image:

Wrong – The duct for this kitchen exhaust fan is made of flex duct instead of smooth metal duct and the duct is not properly supported.

Wrong – The duct for this kitchen exhaust fan is made of flex duct instead of smooth metal duct and the duct is not properly supported.
Image:

Wrong – the exhaust terminal for a clothes dryer should not be covered with a screen which could trap lint; instead, cover it with a hooded, louvered damper

Wrong – the exhaust terminal for a clothes dryer should not be covered with a screen which could trap lint; instead, cover it with a hooded, louvered damper
Image:

Wrong – the interior seam of the branch duct to trunk duct juncture is sealed with mastic but there are gaps around the exterior seam that should also be sealed with mastic or metal tape.

Wrong – the interior seam of the branch duct to trunk duct juncture is sealed with mastic but there are gaps around the exterior seam that should also be sealed with mastic or metal tape.
Image:

Wrong – The kitchen exhaust fan duct is attached to flex duct, which is prohibited by code.

Wrong – The kitchen exhaust fan duct is attached to flex duct, which is prohibited by code.
Image:

Wrong – The plastic seal of the open end of this duct is ripped; the test measurement will overestimate the duct leakage if the temporary seals are not very carefully completed

Wrong – The plastic seal of the open end of this duct is ripped; the test measurement will overestimate the duct leakage if the temporary seals are not very carefully completed
Image:

Wrong – These flex ducts are pulled taut, which is correct but they are inadequately supported with straps that are spaced too far apart and are too tight causing pinching of the insulation and turns are sharp rather than gradual.

Wrong – These flex ducts are pulled taut, which is correct but they are inadequately supported with straps that are spaced too far apart and are too tight causing pinching of the insulation and turns are sharp rather than gradual.
Image:

Wrong – This damper is closed, so the duct system is not entirely pressurized during the duct leakage test

Wrong – This damper is closed, so the duct system is not entirely pressurized during the duct leakage test