Skip to main content

Resources

Explore a library of home construction and renovation guidance and easily search through galleries containing hundreds of building science-related photos, drawings, videos, CAD files, case studies, and presentations.

Filter

View Library

Showing 1057 - 1080 of 1354 results:

Image:

The ability to choose a light color range allows one to customize the lighting of any space

The ability to choose a light color range allows one to customize the lighting of any space
Image:

The advance-framed 2x6 24-inch on-center walls are covered with netting then filled with R-23 blown fiberglass.

The advance-framed 2x6 24-inch on-center walls are covered with netting then filled with R-23 blown fiberglass.
Image:

The application of intumescent coating/protection layer protects this elevated floor system from below.

The application of intumescent coating/protection layer protects this elevated floor system from below.
Image:

The attic duct chase insulated and sealed to the attic floor with spray foam

The attic duct chase insulated and sealed to the attic floor with spray foam
Image:

The attic is insulated along the underside of the roof deck with 8 inches of open-cell spray foam.

The attic is insulated along the underside of the roof deck with 8 inches of open-cell spray foam.
Image:

The attic is sealed and insulated along the underside of the roof deck with 5.5 inches of polyurethane spray foam, providing conditioned space for the HVAC system.

The attic is sealed and insulated along the underside of the roof deck with 5.5 inches of polyurethane spray foam, providing conditioned space for the HVAC system.
Image:

The attic knee walls were constructed from 2x6s and insulated with R-19 batt, backed with 1 inch of XPS foam board with taped joints to provide a solid air barrier over the insulated surfaces.

The attic knee walls were constructed from 2x6s and insulated with R-19 batt, backed with 1 inch of XPS foam board with taped joints to provide a solid air barrier over the insulated surfaces.
Image:

The attic kneewall and the open floor cavities under kneewall are both sealed and insulated in one step with spray foam insulation

The attic kneewall and the open floor cavities under kneewall are both sealed and insulated in one step with spray foam insulation
Image:

The baffle is air sealed in place with spray foam before installing fiberglass or cellulose insulation

The baffle is air sealed in place with spray foam before installing fiberglass or cellulose insulation
Image:

The base of the plywood parapet is air sealed with spray foam and fibrous insulation is installed in the rafter cavities in this flat roof retrofit

The base of the plywood parapet is air sealed with spray foam and fibrous insulation is installed in the rafter cavities in this flat roof retrofit
Image:

The basement is constructed with precast concrete walls lined with R-21.3 foil-faced rigid foam while an R-10 layer of XPS rigid foam covers the ground under the slab.

The basement is constructed with precast concrete walls lined with R-21.3 foil-faced rigid foam while an R-10 layer of XPS rigid foam covers the ground under the slab.
Image:

The basement slab is wrapped in a blanket of insulation including R-27 of closed-cell spray foam under the slab and R-22 ICF blocks wrapping the slab edges.

The basement slab is wrapped in a blanket of insulation including R-27 of closed-cell spray foam under the slab and R-22 ICF blocks wrapping the slab edges.
Image:

The basement walls’ interior framing is set in 3 inches from the concrete to allow space for closed-cell foam that is sprayed directly on the concrete, then blown cellulose is added to fill the wall cavity.

The basement walls’ interior framing is set in 3 inches from the concrete to allow space for closed-cell foam that is sprayed directly on the concrete, then blown cellulose is added to fill the wall cavity.
Image:

The batt insulation shown here was properly installed to fill the ceiling cavities.

The batt insulation shown here was properly installed to fill the ceiling cavities.
Image:

The builder in this very cold climate installed three layers of unfaced mineral wool batt in the double wall with a code-required vapor barrier between the middle and inner layers of wall insulation that is taped to barriers in the ceiling and floor.

The builder in this very cold climate installed three layers of unfaced mineral wool batt in the double wall with a code-required vapor barrier between the middle and inner layers of wall insulation that is taped to barriers in the ceiling and floor.
Image:

The builder installed 1.5 inches of soy-based spray foam on the outside of the walls over the OSB sheathing, then kept a ¾ inch gap between the foam and the brick veneer siding to allow moisture vapor from the bricks to dissipate.

The builder installed 1.5 inches of soy-based spray foam on the outside of the walls over the OSB sheathing, then kept a ¾ inch gap between the foam and the brick veneer siding to allow moisture vapor from the bricks to dissipate.
Image:

The builder laid down a 4-inch base of aggregate rock, then covered that with a plastic vapor barrier that is taped at all seams and around all penetrations before installing the rigid foam under-slab insulation.

The builder laid down a 4-inch base of aggregate rock, then covered that with a plastic vapor barrier that is taped at all seams and around all penetrations before installing the rigid foam under-slab insulation.
Image:

The builder was able to pack R-41 of blown fiberglass into the wall cavity formed by the double stud walls.

The builder was able to pack R-41 of blown fiberglass into the wall cavity formed by the double stud walls.
Image:

The builder’s crews spray foam directly onto the ground to provide a vapor barrier and insulation layer under the slab.

The builder’s crews spray foam directly onto the ground to provide a vapor barrier and insulation layer under the slab.
Image:

The builders sprayed the underside of the roof assembly with 6 inches of open-cell spray foam to create an unvented, R-48 insulated attic.

The builders sprayed the underside of the roof assembly with 6 inches of open-cell spray foam to create an unvented, R-48 insulated attic.
Image:

The ceiling over an unconditioned space is insulated with closed-cell spray foam that fills the ceiling cavities and encapsulates the framing

The ceiling over an unconditioned space is insulated with closed-cell spray foam that fills the ceiling cavities and encapsulates the framing
Image:

The dark spots on the ceiling in this infrared camera image likely indicate missing or displaced attic insulation.

The dark spots on the ceiling in this infrared camera image likely indicate missing or displaced attic insulation.
Image:

The daylight basement walls are made of concrete walls with integrated rigid foam and steel-faced concrete studs.

The daylight basement walls are made of concrete walls with integrated rigid foam and steel-faced concrete studs.
Image:

The double walls form a 12-inch cavity that was sheathed with a coated OSB then coated with 3 inches of closed-cell spray foam; they will be filled with 9 inches of blown fiberglass.

The double walls form a 12-inch cavity that was sheathed with a coated OSB then coated with 3 inches of closed-cell spray foam; they will be filled with 9 inches of blown fiberglass.