Skip to main content

Resources

Explore a library of home construction and renovation guidance and easily search through galleries containing hundreds of building science-related photos, drawings, videos, CAD files, case studies, and presentations.

Filter

View Library

Showing 457 - 480 of 653 results:

Image:

The heat pump water heater’s evaporator fan provides enough air movement for active ventilation of a small room when the exhaust is ducted; intake air enters passively through a wall grille

The heat pump water heater’s evaporator fan provides enough air movement for active ventilation of a small room when the exhaust is ducted; intake air enters passively through a wall grille
Image:

The high-efficiency air-to-air heat pump is set in an overflow pan with an emergency shut off sensor in case the condensate tube were to clog and cause condensate to fill up the pan.

The high-efficiency air-to-air heat pump is set in an overflow pan with an emergency shut off sensor in case the condensate tube were to clog and cause condensate to fill up the pan.
Image:

The hole in the air handler box, on left, was covered with a piece of 30-gauge sheet metal that was cut to size and sealed in place with screws and mastic.

The hole in the air handler box, on left, was covered with a piece of 30-gauge sheet metal that was cut to size and sealed in place with screws and mastic.
Image:

The hole in the drywall was cut overly large for this heating register, allowing air to leak into or out of the wall cavities.

The hole in the drywall was cut overly large for this heating register, allowing air to leak into or out of the wall cavities.
Image:

The HVAC ducts are properly supported with wide straps spaced close together.

The HVAC ducts are properly supported with wide straps spaced close together.
Image:

The inner liner of the flex duct is fastened to the collar with a tension tie, the connection is sealed with mastic, then the outer layer is pulled over and sealed with mastic or foil tape (Steven Winter Associates 2013).

The inner liner of the flex duct is fastened to the collar with a tension tie, the connection is sealed with mastic, then the outer layer is pulled over and sealed with mastic or foil tape (Steven Winter Associates 2013).
Image:

The joints in the ducts and air handler are sealed with mastic.

The joints in the ducts and air handler are sealed with mastic.
Image:

The jump duct should be insulated and sealed at registers

The jump duct should be insulated and sealed at registers
Image:

The large hole that was cut in the subfloor penetration for this HVAC duct has been air-sealed using sheet metal, mastic, and metal tape.

The large hole that was cut in the subfloor penetration for this HVAC duct has been air-sealed using sheet metal, mastic, and metal tape.
Image:

The location of furnace and water heater flues can be identified by going outside and looking for metal pipes coming through the roof.

The location of furnace and water heater flues can be identified by going outside and looking for metal pipes coming through the roof.
Image:

The main trunk line of the ducts runs within an insulated duct chase installed in a notch designed into the roof trusses that runs the length of the home to provide supply air directly to most of the home’s ceiling registers.

The main trunk line of the ducts runs within an insulated duct chase installed in a notch designed into the roof trusses that runs the length of the home to provide supply air directly to most of the home’s ceiling registers.
Image:

The manometer hose for a duct leakage test is connected to a static pressure probe which will be inserted into a duct with the tip pointing into the oncoming air stream

The manometer hose for a duct leakage test is connected to a static pressure probe which will be inserted into a duct with the tip pointing into the oncoming air stream
Image:

The natural draft and induced draft furnace are both Category I appliances that receive combustion air from the combustion appliance zone

The natural draft and induced draft furnace are both Category I appliances that receive combustion air from the combustion appliance zone
Image:

The pointed tip of this static pressure probe should point directly upstream into the oncoming airflow

The pointed tip of this static pressure probe should point directly upstream into the oncoming airflow
Image:

The raised hood at the base of the vent stack on this water heater shows that it is an atmospheric vented gas water heater

The raised hood at the base of the vent stack on this water heater shows that it is an atmospheric vented gas water heater
Image:

The round metal HVAC ducts are sealed with mastic at all joints and seams.

The round metal HVAC ducts are sealed with mastic at all joints and seams.
Image:

The sealed, insulated crawlspace is a clean, dry location to house the main floor heating ducts and also provides bonus storage space.

The sealed, insulated crawlspace is a clean, dry location to house the main floor heating ducts and also provides bonus storage space.
Image:

The seam between this duct register and the wood flooring is sealed with caulk to prevent air leakage into the house from the crawlspace below.

The seam between this duct register and the wood flooring is sealed with caulk to prevent air leakage into the house from the crawlspace below.
Image:

The seams in this HVAC duct are sealed with mastic.

The seams in this HVAC duct are sealed with mastic.
Image:

The single strap cannot support the bend and is nearly severing the flex duct

The single strap cannot support the bend and is nearly severing the flex duct
Image:

The tape is covered with mastic to ensure an airtight seal between the duct and the fitting

The tape is covered with mastic to ensure an airtight seal between the duct and the fitting
Image:

The test fan for this central ERV duct leakage test is connected to the duct system from inside the ERV cabinet

The test fan for this central ERV duct leakage test is connected to the duct system from inside the ERV cabinet
Image:

The test fan for this rooftop duct test is connected to the central exhaust duct via a transition plate at the rooftop curb

The test fan for this rooftop duct test is connected to the central exhaust duct via a transition plate at the rooftop curb
Image:

The unsealed register boot is going through the side wall of the chase

The unsealed register boot is going through the side wall of the chase