Library

2009 edition of code for commercial buildings that brings together all structural, plumbing, mechanical, fuel gas, energy and electrical provisions for all buildings except detached one- and two-family residences and townhouses up to three stories.

2009 edition of code establishing a baseline for the design and installation of fuel gas systems and gas fired appliances through performance requirements.

2009 edition of code establishing minimum regulations for plumbing facilities, including fixtures, water heaters, water supply and distribution, sanitary drainage, storm drainage, etc.

2009 edition of code for residential buildings that creates minimum regulations for one- and two-family dwellings of three stories or less, bringing together all building, plumbing, mechanical, fuel gas, energy and electrical provisions for one- and two-family residences.

2012 edition of code establishing minimum regulations for plumbing facilities, including fixtures, water heaters, water supply and distribution, sanitary drainage, storm drainage, etc.

Florida building code including all the amendments and additions by Florida for the wind-borne debris regions and the high-velocity hurricane zone.

Document describing portions of the flood provisions from the 2018 editions of the IBC, IRC, IEBC, IMC, IPC, IFGC, IFC, ISPSC, IPSDC, and ICC Performance Code.

A colored map showing seismic zones across the United States, ranging from lowest to highest seismic hazards.

Report assessing and scoring code enforcement and administration and contractor licensing in the 18 states most vulnerable to catastrophic hurricanes along the Atlantic Coast and the Gulf of Mexico.

Code set from IAPMO explaining plumbing standards. 2018 publication.

Article describing products that can enhance the efficiency and safety of clothes dryer vents.

Report providing builders in marine climates with guidance for building homes that have whole-house energy savings of 40% over the Building America benchmark with no added overall costs for consumers.

Article from the Sierra Club explaining 5 steps to take to ensure your home's resistance to wildfires, including site maintenance and roof construction guidelines.

Article describing seven reasons to mulch gardens.

Paper describing a proposed method for quantifying tree and vegetation evapotranspiration effects on city climate

Report describing an air distribution system composed of a series of uniformly-sized ducts that terminate in rooms throughout the home and return to a central manifold, similar in fashion to a “home-run” cross-linked polyethylene plumbing system.

Article describing methods for thermally isolating a garage in a Passive House-certified multifamily building.

Technical manual from ACCA outlining correct methods for zoning of residential HVAC systems.

This Standard establishes the minimum requirements to evaluate a residence with regards to energy efficiency, water conservation, occupant comfort, and indoor air quality.

Report describing advanced framing techniques, including discussion of cost and energy savings.

Report describing the experience gained from AIA’s Disaster Assistance Program with first-hand accounts of disaster response and recovery, case studies and other best practices, including approaches to designing buildings to be more adaptable to uncertainty.

Article describing how an airtight home shell helps achieve a tight envelope that is energy efficient and cost effective.

Article describing air sealing and air barriers in buildings.

Webpage providing mapping tool for obtaining ground snow load, based on ASCE 7-10, for any location in the contiguous United States, with the exception of locations requiring a case study due to extreme local variations in ground snow loads. Fee required for some data.

Standard establishing the minimum whole-building energy performance requirements for energy efficient residential buildings.

Technical fact sheet describing ways to construct asphalt shingle roofs to be more resistant to high winds and hurricanes; also published in FEMA P-499 “Home Builder’s Guide to Coastal Construction: Technical Fact Sheet Series.”

Fact sheet describing recommended practices for installing brick veneer that will enhance wind resistance in high wind regions and examples of proper installations and brick veneer tie spacings; also published in FEMA P-499 “Home Builder’s Guide to Coastal Construction: Technical Fact Sheet Series.”

Document providing background and approach for the prep work necessary prior to adding attic insulation - focusing on combustion safety, ventilation for indoor air quality, and attic ventilation for durability.

This report outlines research activities that are expected to facilitate the adoption of energy retrofits by remodeling contractors and roofing contractors using retrofit panels which applicable to many existing house designs in most climates and markets.

Report covering interior energy retrofits of masonry buildings.

Article describing the building science implications of insulating vented or unvented attics.

Article describing the research into insulating vented versus unvented attics.

Article describing different kinds of water-resistant backer boards.

Information sheet from FEMA on preparation for extreme heat, including measures for keeping homes cool.

This Best Practices Manual is the product of Hammer & Hand’s ongoing work to document and internally codify our standard operating procedures for construction practice.

Code establishing the rules of safety relating only to pressure integrity for the design, fabrication, and inspection of boilers and pressure vessels during construction which was published in the year 2017 and is available to order at the referenced link.

Webinar answering code-related questions on duct leakage tests, moisture levels in attics and crawlspaces, combustion equipment in conditioned attics, ventilation in multifamily buildings, and continuous insulation in residential construction.

Report providing water management details for roof assemblies.

Document providing guidance to U.S. home builders who want to accept the challenge.

Report examining the cost differences between a typical home and a home constructed using wildfire-resistant materials and design features.

Report summarizing the guidelines for developing and reporting analytical results in a consistent and meaningful manner for all home energy uses.

Report investigating implementation of advanced framing in both production and prototype built homes built in a variety of climate regions across the USA.

Research study describing a number of promising foundation and basement insulation strategies that can meet the requirement for better thermal control in colder climates while enhancing moisture control, health, and comfort.

Report comparing a variety of roof insulating strategies to present their advantages and disadvantages according to several comparison criteria.

Document providing an example procedure for establishing acceptance-range criteria to assess results from software undergoing BESTEST-EX.

Article describing the control layers (air, thermal, and vapor barriers) needed to build homes successfully in very cold locations.

Article published by American Society of Civil Engineers on different building types and their effectiveness resisting extreme heat from a building envelope perspective.

Report describing ventilation system design, including a central fan integrated supply (CFIS) system, made up of a 6-inch outdoor air intake duct connected to the return side of the air handler with a fan cycling control to make sure the fan runs a programmed minimum amount of time.

You can save energy and maintain a comfortable swimming pool temperature by using a smaller, higher efficiency pump and by operating it less.

Website providing weather data.