Library

Fact sheet describing a report providing best practices for reducing damages from floods to manufactured homes.

Fact sheet providing an overview of the FEMA document Wind Retrofit Guide for Residential Buildings.

2009 edition of code for commercial buildings that brings together all structural, plumbing, mechanical, fuel gas, energy and electrical provisions for all buildings except detached one- and two-family residences and townhouses up to three stories.

2012 edition of code establishing a baseline for energy efficiency by setting performance standards for the building envelope (defined as the boundary that separates heated/cooled air from unconditioned, outside air), mechanical systems, lighting systems and service water heating systems in homes...

2012 edition of code establishing a baseline for the design and installation of fuel gas systems and gas fired appliances through performance requirements.

2012 edition of code establishing minimum regulations for mechanical systems, including heating, cooling, ventilation, exhaust, ducts, fireplaces, combustion and hydronic systems, using prescriptive and performance-related provisions.

2012 edition of code for residential buildings that creates minimum regulations for one- and two-family dwellings of three stories or less, bringing together all building, plumbing, mechanical, fuel gas, energy and electrical provisions for one- and two-family residences.

Report summarizing the requirements to strenghthen new homes against property damage caused by high wind occurrences per the IBHS Fortified Homes High Wind Standard for New Homes.

Fact sheet summarizing the changes to the flood provisions in the 2012 I-Codes that appear in the 2015 edition.

Document describing the air leakage provisions of Appendix RA of the 2015 IECC (prepared for the State of Georgia to assist with compliance with their 2019 Energy Code).

2015 edition of code establishing minimum regulations for mechanical systems, including heating, cooling, ventilation, exhaust, ducts, fireplaces, combustion and hydronic systems, using prescriptive and performance-related provisions.

Guide providing engineering seismic design and building practices based on post-earthquake research.

Federal statistics about national energy consumption in residential homes.

Code set from IAPMO explaining plumbing standards. 2015 publication.

Fact sheet providing an overview of FEMA P-348, Protecting Building Utility Systems From Flood Damage.

Report summarizing the requirements for strenghtening and protecting the roof, openings in the house, and creating a continuous load path to strengthen walls and foundation per the IBHS Fortified Homes Hurricane Standard for New Homes.

Standard providing a methodology for calculating Energy Rating Index for code compliance.

Guide describing the requirements by FORTIFIED Home™ for improving the home's resistance in severe thunderstorms, straight-line wind events, and high winds at the outer edges of tornadoes.

Article describing products that can enhance the efficiency and safety of clothes dryer vents.

Report providing builders in marine climates with guidance for building homes that have whole-house energy savings of 40% over the Building America benchmark with no added overall costs for consumers.

Report describing how changing the air exchange rate of a home (the sum of the infiltration and mechanical ventilation airflow rates) affects the annual thermal conditioning energy.

Standard providing master specifications for closed cell, medium density spray polyurethane foam air barriers located in the non-accessible part of the wall.

Standard providing information about self-adhered sheet air barriers located in the non-accessible part of the wall and materials to bridge and seal air leakage pathways and gaps.

The manual covers residential zoning issues - multiple, single-zone, and central multi-zone systems - and includes advice on working with homeowners to adapt the heating or cooling system design to meet modern home design features.

Standard providing nationally recognized, manufacturer-endorsed set of inspection tasks for HVAC maintenance.

Case study on the design and evaluation of extended plate and beam, located in Mount Joy Pennsylvania.

Report describing advanced framing techniques, including discussion of cost and energy savings.

Fact sheet describing air-sealing concerns and remedies, including HRV/ERV installation, caulking, spray foam, and weatherstrip installation.

Report on adding insulation to load-bearing mass masonry buildings.

Report analyzing design heating load sizing methods for superinsulated homes in cold climates and comparing them to the actual energy usage to determine if the building load calculation methodology should be changed for calculating the design heating load of these homes.

A publication highlighting recommendations that contribute to improved overall performance in the structural shell and focus on good connection details to tie together exterior walls, roofs and floors.

Guidance from HUD, EPA, NIH, and FEMA for workers who deal directly with asbestos.

Technical fact sheet describing ways to construct asphalt shingle roofs to be more resistant to high winds and hurricanes; also published in FEMA P-499 “Home Builder’s Guide to Coastal Construction: Technical Fact Sheet Series.”

Report describing the business case of hosting a Level 2 electric vehicle (EV) charging station in New York, including analysis of real-world data on equipment use, costs, revenue, and assumptions derived from industry reports and original research.

Fact sheet describing recommended practices for installing brick veneer that will enhance wind resistance in high wind regions and examples of proper installations and brick veneer tie spacings; also published in FEMA P-499 “Home Builder’s Guide to Coastal Construction: Technical Fact Sheet Series.”

Document providing background and approach for the prep work necessary prior to adding attic insulation - focusing on combustion safety, ventilation for indoor air quality, and attic ventilation for durability.

Article describing different kinds of water-resistant backer boards.

Webpage from Suntegrity Solar describing different backup power generator options to prepare for future power outages.

This directory contains the I=B=R Ratings for cast-iron, steel, aluminum and copper boilers, baseboard and finned tube radiation, indirect-fired water heaters, effective as of the date of this publication.

Document providing guidance to U.S. home builders who want to accept the challenge.

A book about structurally insulated panels.

Web based tool providing decision-making guidance for selecting wall assembly components.

Report summarizing the guidelines for developing and reporting analytical results in a consistent and meaningful manner for all home energy uses.

Report presenting the building america research to market plan.

Report investigating implementation of advanced framing in both production and prototype built homes built in a variety of climate regions across the USA.

Research study describing a number of promising foundation and basement insulation strategies that can meet the requirement for better thermal control in colder climates while enhancing moisture control, health, and comfort.

Report comparing a variety of roof insulating strategies to present their advantages and disadvantages according to several comparison criteria.

Document providing an example procedure for establishing acceptance-range criteria to assess results from software undergoing BESTEST-EX.

Article describing the control layers (air, thermal, and vapor barriers) needed to build homes successfully in very cold locations.

Document presenting some of the key technical properties of many of the most common building materials.