Library

2009 edition of code for commercial buildings that brings together all structural, plumbing, mechanical, fuel gas, energy and electrical provisions for all buildings except detached one- and two-family residences and townhouses up to three stories.

2009 edition of code establishing a baseline for the design and installation of fuel gas systems and gas fired appliances through performance requirements.

2009 edition of code establishing minimum regulations for plumbing facilities, including fixtures, water heaters, water supply and distribution, sanitary drainage, storm drainage, etc.

2009 edition of code for residential buildings that creates minimum regulations for one- and two-family dwellings of three stories or less, bringing together all building, plumbing, mechanical, fuel gas, energy and electrical provisions for one- and two-family residences.

2012 edition of code establishing minimum regulations for plumbing facilities, including fixtures, water heaters, water supply and distribution, sanitary drainage, storm drainage, etc.

Florida building code including all the amendments and additions by Florida for the wind-borne debris regions and the high-velocity hurricane zone.

Document describing portions of the flood provisions from the 2018 editions of the IBC, IRC, IEBC, IMC, IPC, IFGC, IFC, ISPSC, IPSDC, and ICC Performance Code.

A colored map showing seismic zones across the United States, ranging from lowest to highest seismic hazards.

Report assessing and scoring code enforcement and administration and contractor licensing in the 18 states most vulnerable to catastrophic hurricanes along the Atlantic Coast and the Gulf of Mexico.

Code set from IAPMO explaining plumbing standards. 2018 publication.

Article from the Sierra Club explaining 5 steps to take to ensure your home's resistance to wildfires, including site maintenance and roof construction guidelines.

Article describing seven reasons to mulch gardens.

Paper describing a proposed method for quantifying tree and vegetation evapotranspiration effects on city climate

Report describing an air distribution system composed of a series of uniformly-sized ducts that terminate in rooms throughout the home and return to a central manifold, similar in fashion to a “home-run” cross-linked polyethylene plumbing system.

Article describing methods for thermally isolating a garage in a Passive House-certified multifamily building.

Technical manual from ACCA outlining correct methods for zoning of residential HVAC systems.

This Standard establishes the minimum requirements to evaluate a residence with regards to energy efficiency, water conservation, occupant comfort, and indoor air quality.

Report describing the experience gained from AIA’s Disaster Assistance Program with first-hand accounts of disaster response and recovery, case studies and other best practices, including approaches to designing buildings to be more adaptable to uncertainty.

Article describing how an airtight home shell helps achieve a tight envelope that is energy efficient and cost effective.

Article describing air sealing and air barriers in buildings.

Webpage providing mapping tool for obtaining ground snow load, based on ASCE 7-10, for any location in the contiguous United States, with the exception of locations requiring a case study due to extreme local variations in ground snow loads. Fee required for some data.

Standard establishing the minimum whole-building energy performance requirements for energy efficient residential buildings.

This report outlines research activities that are expected to facilitate the adoption of energy retrofits by remodeling contractors and roofing contractors using retrofit panels which applicable to many existing house designs in most climates and markets.

Report covering interior energy retrofits of masonry buildings.

Technical article describing issues and moisture concerns related to weatherization efforts.

Article describing the building science implications of insulating vented or unvented attics.

Article describing the research into insulating vented versus unvented attics.

Information sheet from FEMA on preparation for extreme heat, including measures for keeping homes cool.

This Best Practices Manual is the product of Hammer & Hand’s ongoing work to document and internally codify our standard operating procedures for construction practice.

Code establishing the rules of safety relating only to pressure integrity for the design, fabrication, and inspection of boilers and pressure vessels during construction which was published in the year 2017 and is available to order at the referenced link.

Webinar answering code-related questions on duct leakage tests, moisture levels in attics and crawlspaces, combustion equipment in conditioned attics, ventilation in multifamily buildings, and continuous insulation in residential construction.

Report providing water management details for roof assemblies.

Report examining the cost differences between a typical home and a home constructed using wildfire-resistant materials and design features.

Article published by American Society of Civil Engineers on different building types and their effectiveness resisting extreme heat from a building envelope perspective.

Case study characterizing the framing factors for the exterior walls, ceilings, and floors of 180 wood-framed low-rise residential buildings across the United States.

You can save energy and maintain a comfortable swimming pool temperature by using a smaller, higher efficiency pump and by operating it less.

Website providing weather data.

Report assessing the science of climate change with a focus on the U.S.

ENERGY STAR clothes dryer buying guidance for consumers.

Part I of the Guide addresses walls constructed with 2x6 wood frame studs, wood structural panel (WSP) sheathing as exterior sheathing, gypsum board as interior sheathing, and a cladding system installed over WSP sheathing in low-rise residential buildings up to three stories in height. Walls with...

The Guide addresses walls constructed with 2x4 wood frame studs, wood structural panel sheathing (WSP) as wall bracing and added backing for foam sheathing, a layer of rigid foam sheathing insulation up to 1.5 inches thick over the WSP, and a cladding system installed over the foam sheathing in low...

Part I of the Guide addresses walls constructed with 2x6 wood frame studs, wood structural panel (WSP) sheathing as exterior sheathing, gypsum board as interior sheathing, and a cladding system installed over WSP sheathing in low-rise residential buildings up to three stories in height.

The Guide addresses walls constructed with 2x4 wood frame studs, wood structural panel (WSP) sheathing as wall bracing and added backing for foam sheathing, a layer of rigid foam sheathing insulation up to 1.5 in. thick over the WSP, and a cladding system installed over the foam sheathing in low...

Article describing the use of whole-house fans to provide cooling in the region surrounding Sacramento, CA.

Tool developed by LBNL to calculate potential savings from increasing wall and roof solar reflectance.

Article describing the importance of air sealing, insulation, and roof ventilation in reducing the likelihood of ice dam formation on roofs in cold snowy climates.

Information sheet with safety tips for home owners on proper maintenance of clothes dryers.

A quick guide from the California Division of the State Architect (DSA) explaining the three types of gas shutoff devices to stop the flow of natural gas into buildings in the event of an earthquake or rupture of the gas line.

Document explaining requirements and recommendations for defensible space, with a focus on sloped vegetation.

Report describing guidance for selecting an electric vehicle charger