Library

2009 edition of code establishing minimum regulations for plumbing facilities, including fixtures, water heaters, water supply and distribution, sanitary drainage, storm drainage, etc.

2012 edition of code establishing minimum regulations for plumbing facilities, including fixtures, water heaters, water supply and distribution, sanitary drainage, storm drainage, etc.

A colored map showing seismic zones across the United States, ranging from lowest to highest seismic hazards.

Report assessing and scoring code enforcement and administration and contractor licensing in the 18 states most vulnerable to catastrophic hurricanes along the Atlantic Coast and the Gulf of Mexico.

Code set from IAPMO explaining plumbing standards. 2018 publication.

Article describing products that can enhance the efficiency and safety of clothes dryer vents.

Report providing builders in marine climates with guidance for building homes that have whole-house energy savings of 40% over the Building America benchmark with no added overall costs for consumers.

Technical manual from ACCA outlining correct methods for zoning of residential HVAC systems.

This Standard establishes the minimum requirements to evaluate a residence with regards to energy efficiency, water conservation, occupant comfort, and indoor air quality.

Report describing advanced framing techniques, including discussion of cost and energy savings.

Article describing how an airtight home shell helps achieve a tight envelope that is energy efficient and cost effective.

Article describing air sealing and air barriers in buildings.

Standard establishing the minimum whole-building energy performance requirements for energy efficient residential buildings.

Technical fact sheet describing ways to construct asphalt shingle roofs to be more resistant to high winds and hurricanes; also published in FEMA P-499 “Home Builder’s Guide to Coastal Construction: Technical Fact Sheet Series.”

Fact sheet describing recommended practices for installing brick veneer that will enhance wind resistance in high wind regions and examples of proper installations and brick veneer tie spacings; also published in FEMA P-499 “Home Builder’s Guide to Coastal Construction: Technical Fact Sheet Series.”

Document providing background and approach for the prep work necessary prior to adding attic insulation - focusing on combustion safety, ventilation for indoor air quality, and attic ventilation for durability.

This report outlines research activities that are expected to facilitate the adoption of energy retrofits by remodeling contractors and roofing contractors using retrofit panels which applicable to many existing house designs in most climates and markets.

Report covering interior energy retrofits of masonry buildings.

Technical article describing issues and moisture concerns related to weatherization efforts.

Article describing the building science implications of insulating vented or unvented attics.

Article describing the research into insulating vented versus unvented attics.

Article describing different kinds of water-resistant backer boards.

Information sheet from FEMA on preparation for extreme heat, including measures for keeping homes cool.

This Best Practices Manual is the product of Hammer & Hand’s ongoing work to document and internally codify our standard operating procedures for construction practice.

Document providing guidance to U.S. home builders who want to accept the challenge.

Report examining the cost differences between a typical home and a home constructed using wildfire-resistant materials and design features.

Report summarizing the guidelines for developing and reporting analytical results in a consistent and meaningful manner for all home energy uses.

Report investigating implementation of advanced framing in both production and prototype built homes built in a variety of climate regions across the USA.

Research study describing a number of promising foundation and basement insulation strategies that can meet the requirement for better thermal control in colder climates while enhancing moisture control, health, and comfort.

Report comparing a variety of roof insulating strategies to present their advantages and disadvantages according to several comparison criteria.

Document providing an example procedure for establishing acceptance-range criteria to assess results from software undergoing BESTEST-EX.

Article describing the control layers (air, thermal, and vapor barriers) needed to build homes successfully in very cold locations.

Report describing ventilation system design, including a central fan integrated supply (CFIS) system, made up of a 6-inch outdoor air intake duct connected to the return side of the air handler with a fan cycling control to make sure the fan runs a programmed minimum amount of time.

Case study characterizing the framing factors for the exterior walls, ceilings, and floors of 180 wood-framed low-rise residential buildings across the United States.

You can save energy and maintain a comfortable swimming pool temperature by using a smaller, higher efficiency pump and by operating it less.

Fact sheet providing guidance and best practices on the selection of building materials used for coastal construction, and discussing flood, wind, corrosion, decay resistance, and protection recommendations; also published in FEMA P-499 “Home Builder’s Guide to Coastal Construction: Technical Fact...

Fact sheet describing the characteristics that make for a successful coastal residential building, including design and construction recommendations; also published in FEMA P-499 “Home Builder’s Guide to Coastal Construction: Technical Fact Sheet Series.”

Installation manual describing proper installation practices, industry standards and the code requirements of roofing tiles.

Article describing the use of whole-house fans to provide cooling in the region surrounding Sacramento, CA.

Tool developed by LBNL to calculate potential savings from increasing wall and roof solar reflectance.

Article describing the importance of air sealing, insulation, and roof ventilation in reducing the likelihood of ice dam formation on roofs in cold snowy climates.

Fact sheet summarizing NFIP requirements, general guidelines, and recommendations concerning the construction and installation of decks, access stairs and elevators, swimming pools, and accessory buildings under or near coastal residential buildings; also published in FEMA P-499 “Home Builder’s...

Fact sheet describing design and construction practices that reduce the likelihood of flood damage in the event that flood levels exceed the BFE, including illustrations of appropriate construction practices; also published in FEMA P-499 “Home Builder’s Guide to Coastal Construction: Technical Fact...

Document providing design guidance and software tool information for forced-air HVAC systems.

Information about dense pack, cellulose insulation.

Information sheet with safety tips for home owners on proper maintenance of clothes dryers.

A quick guide from the California Division of the State Architect (DSA) explaining the three types of gas shutoff devices to stop the flow of natural gas into buildings in the event of an earthquake or rupture of the gas line.

Information sheet with HVAC duct insulation, testing, maintenance and performance information.

Report providing an introduction to the NEHRP recommended seismic provisions for new buildings and other structures.

Presentation describing the history of ECM motors, an overview of ECM motor technology, and a lesson on the installation of ECM motors.