Library

2009 edition of code establishing minimum regulations for plumbing facilities, including fixtures, water heaters, water supply and distribution, sanitary drainage, storm drainage, etc.

2012 edition of code establishing minimum regulations for plumbing facilities, including fixtures, water heaters, water supply and distribution, sanitary drainage, storm drainage, etc.

Standard providing a methodology for calculating Energy Rating Index for code compliance.

2015 edition of code establishing a baseline for energy efficiency by setting performance standards for the building envelope (defined as the boundary that separates heated/cooled air from unconditioned, outside air), mechanical systems, lighting systems and service water heating systems in homes...

2015 edition of code establishing regulations involving life and property safety from fires and explosion hazards, including emergency planning, fire department access and water supply, automatic sprinkler systems, fire alarms, and hazardous materials planning and storage.

2015 edition of code establishing a baseline for the design and installation of fuel gas systems and gas fired appliances through performance requirements.

A colored map showing seismic zones across the United States, ranging from lowest to highest seismic hazards.

Report assessing and scoring code enforcement and administration and contractor licensing in the 18 states most vulnerable to catastrophic hurricanes along the Atlantic Coast and the Gulf of Mexico.

Code set from IAPMO explaining plumbing standards. 2018 publication.

Report telling consumers the risks of radon, how radon gets into a home, and steps consumers can take to reduce radon exposure in their homes.

Guide for homeowners describing how to find and seal basement and attic air leaks, determine if attic insulation is adequate, make improvements safely, and reduce energy bills.

Standards book discussing the minimum standards of total system balance of HVAC systems.

Vinyl siding estimating and installation guide for vinyl siding products.

Standard outlining industry procedure for sizing residential duct systems.

Standard covering equipment sizing loads for single-family-detached homes, small multi-unit structures, condo­miniums, town houses and manufactured homes.

Technical manual from ACCA outlining correct methods for zoning of residential HVAC systems.

This Standard establishes the minimum requirements to evaluate a residence with regards to energy efficiency, water conservation, occupant comfort, and indoor air quality.

Standard providing a universally accepted definition for quality installation for residential and commercial heating, ventilating, and air conditioning applications.

Document detailing the requirements, roles, and obligations for participants in an organized effort, ensuring that HVAC installations comply with the ANSI/ACCA 5 QI – 2010 (HVAC Quality Installation Specification) QI Standard.

Acceptance criteria providing guidelines for demonstrating compliance with codes referenced in the criteria related to barriers to water migration in thin-set installations of ceramic tile and stone flooring and shower sub-pan linings.

Article describing how to detail head flashing above a window.

Report on the design and evaluation of extended plate and beam.

Report describing approaches to using less wood in home building that minimize waste.

Fact sheet describing advanced wall framing.

Article describing recessed lighting, which if installed incorrectly may contribute to air leakage and compromise building envelope efficiency.

Article describing how an airtight home shell helps achieve a tight envelope that is energy efficient and cost effective.

Updated detailed information about Formaldehyde.

Report describing a field investigation of failure rates of whole-house mechanical ventilation systems installed in Florida homes.

Article describing air sealing and air barriers in buildings.

Standard establishing the minimum whole-building energy performance requirements for energy efficient residential buildings.

A basic guide walking through the various types of valves useful in mitigating the effects of earthquakes and other seismic events on natural gas pipelines for residential use.

This report outlines research activities that are expected to facilitate the adoption of energy retrofits by remodeling contractors and roofing contractors using retrofit panels which applicable to many existing house designs in most climates and markets.

Report covering interior energy retrofits of masonry buildings.

Article describing the building science implications of insulating vented or unvented attics.

Article describing the research into insulating vented versus unvented attics.

Report describing approaches to insulating basements in homes built to meet Energy Star levels of performance of heat loss reduction.

Fact sheet describing basement insulation considerations.

Information sheet from FEMA on preparation for extreme heat, including measures for keeping homes cool.

This Best Practices Manual is the product of Hammer & Hand’s ongoing work to document and internally codify our standard operating procedures for construction practice.

Report examining the cost differences between a typical home and a home constructed using wildfire-resistant materials and design features.

An article discussing how different metal roof materials and attachment methods affect the ability of the roof to thermally expand and contract and the durability of different solutions.

Information sheet containing images and descriptions of cantilevers.

You can save energy and maintain a comfortable swimming pool temperature by using a smaller, higher efficiency pump and by operating it less.

Report describing combined space- and water-heating (combi) systems using a high-efficiency direct-vent burner.

Fact sheet that details the steps needed to perform a combustion appliance safety inspection to determine if fossil fuel-fired appliances are operating safely under a depressurized condition.

Report describing how space-conditioning systems are operating in the field and if these systems are meeting required standards.

Report outlining the steps developers can take to create high-performance standards on a community-wide scale.

Report on heating and cooling air-distribution ducts that are insulated, installed close to the ceiling in a vented attic and covered with attic insulation to minimize energy loss.

Study investigating measured cooling energy performance in side-by-side identical homes with varying roof types, including cool roof technologies.

Report telling consumers how radon gets into a home and how to reduce radon entry into a home.