Library

2012 edition of code establishing a baseline for energy efficiency by setting performance standards for the building envelope (defined as the boundary that separates heated/cooled air from unconditioned, outside air), mechanical systems, lighting systems and service water heating systems in homes...

2012 edition of code establishing a baseline for the design and installation of fuel gas systems and gas fired appliances through performance requirements.

Report summarizing the requirements to strenghthen new homes against property damage caused by high wind occurrences per the IBHS Fortified Homes High Wind Standard for New Homes.

Fact sheet summarizing the changes to the flood provisions in the 2012 I-Codes that appear in the 2015 edition.

Document describing the air leakage provisions of Appendix RA of the 2015 IECC (prepared for the State of Georgia to assist with compliance with their 2019 Energy Code).

2015 edition of code establishing minimum regulations for mechanical systems, including heating, cooling, ventilation, exhaust, ducts, fireplaces, combustion and hydronic systems, using prescriptive and performance-related provisions.

Guide providing engineering seismic design and building practices based on post-earthquake research.

Federal statistics about national energy consumption in residential homes.

Code set from IAPMO explaining plumbing standards. 2015 publication.

Guide describing the requirements by FORTIFIED Home™ for improving the home's resistance in severe thunderstorms, straight-line wind events, and high winds at the outer edges of tornadoes.

Report describing how changing the air exchange rate of a home (the sum of the infiltration and mechanical ventilation airflow rates) affects the annual thermal conditioning energy.

Document describing three methods for elevating a home out of the flood zone.

Link to the most recent version of ACCA Manual D, a standard outlining industry procedure for sizing residential duct systems.

Link to the most recent version of ACCA Manual J, a standard for producing HVAC equipment sizing loads for single-family detached homes, small multi-unit structures, condominiums, townhouses, and manufactured home

The manual covers residential zoning issues - multiple, single-zone, and central multi-zone systems - and includes advice on working with homeowners to adapt the heating or cooling system design to meet modern home design features.

Link to the most recent version of ACCA Manual S, a standard covering sizing strategies for all types of cooling and heating equipment, as well as how to use comprehensive manufacturer’s performance data on sensible, latent, or heating capacity for various operating conditions.

Case study on the design and evaluation of extended plate and beam, located in Mount Joy Pennsylvania.

Fact sheet describing advanced framing techniques that reduce the amount of lumber used in constructing wood-framed houses while providing more space for wall insulation.

Website describing indoor air quality, and common indoor pollutants and how to reduce exposure to them.

Article describing technologies available for monitoring indoor air quality (IAQ).

Website describing archived program inforamtion for the Air Sensors International Conference, hosted by the University of California, Davis.

Website describing electric vehicles, electric vehicle charging stations, and incentives for installing electric vehicle charging stations.

Regulatory Compliance Toolbox by the American Home Furnishings Alliance (AHFA) concerning health, safety, environmental, fashion and business information related to home furnishings.

Library describing ANSI-affiliated standards.

Report on adding insulation to load-bearing mass masonry buildings.

Report analyzing design heating load sizing methods for superinsulated homes in cold climates and comparing them to the actual energy usage to determine if the building load calculation methodology should be changed for calculating the design heating load of these homes.

Guidance from HUD, EPA, NIH, and FEMA for workers who deal directly with asbestos.

Document describing recent discussions on indoor carbon dioxide (CO 2) levels.

This standard provides the minimum requirements for energy-efficient design of most sites and buildings, except low-rise residential buildings. It offers, in detail, the minimum energy efficiency requirements for design and construction of new sites and buildings and their systems, new portions of...

Articles describing attic and ceiling insulation, including mentions of baffles with protect insulation from wind washing.

Article describing bidirectinoal charging and energy storage methods using electric vehicles.

This directory contains the I=B=R Ratings for cast-iron, steel, aluminum and copper boilers, baseboard and finned tube radiation, indirect-fired water heaters, effective as of the date of this publication.

A book about structurally insulated panels.

Report presenting the building america research to market plan.

Document presenting some of the key technical properties of many of the most common building materials.

An online learning management resource for the construction community.

Webpage providing the latest version of the California Plumbing Code.

Webpage containing the latest version of the California Residential Code.

Webpage describing how caulking is used, how to select the appropriate caulking, and how to apply caulking.

Factsheet describing how caulking is used, how to select the appropriate caulking, and how to apply caulking.

Information sheet with information about insulating and ventilating attics.

Case study about the grid integration of electrical vehicle supply equipment.

Webpage describing electric vehicle chargers

Article describing correct ways to attach rigid insulation to the exterior of commercial and residential buildings.

Report describing strategies to improve the aging steam heating systems in New York City to improve energy efficiency, reduce oil and gas usage, and cut maintenance costs.

Website describing technical expertise and support regarding electric vehicle infrastructure.

Report on improving passive design adoption rates.

Report providing tools and resources to help community planners to improve coastal resilience.

Fact sheet describing what builders need to know about designing a structure for flood loads.

Report on a simplified test procedure for combustion safety that is easier to implement and should produce fewer false positives than the previous procedure.