Library

2012 edition of code establishing a baseline for energy efficiency by setting performance standards for the building envelope (defined as the boundary that separates heated/cooled air from unconditioned, outside air), mechanical systems, lighting systems and service water heating systems in homes...

2012 edition of code establishing a baseline for existing building retrofits to reach appropriate safety levels under new construction requirements covered in other ICC codes.

2012 edition of code establishing regulations involving life and property safety from fires and explosion hazards, including emergency planning, fire department access and water supply, automatic sprinkler systems, fire alarms, and hazardous materials planning and storage.

2012 edition of code establishing a baseline for the design and installation of fuel gas systems and gas fired appliances through performance requirements.

Report describing practices and considerationsfor more efficient water use in pools, spas, and fountains.

Code describing energy codes for energy-conserving and compliant designs in Florida.

The purpose of this standard is to establish minimum requirements to safeguard the public health, safety and general welfare relative to the design, construction and installation of storm shelters constructed for protection from high winds associated with tornadoes and hurricanes.

Report summarizing the requirements to strenghthen new homes against property damage caused by high wind occurrences per the IBHS Fortified Homes High Wind Standard for New Homes.

Fact sheet summarizing the changes to the flood provisions in the 2012 I-Codes that appear in the 2015 edition.

Document describing the air leakage provisions of Appendix RA of the 2015 IECC (prepared for the State of Georgia to assist with compliance with their 2019 Energy Code).

2015 edition of code establishing minimum regulations for mechanical systems, including heating, cooling, ventilation, exhaust, ducts, fireplaces, combustion and hydronic systems, using prescriptive and performance-related provisions.

2015 edition of the code establishing regulations to safeguard life and property from the intrusion of wildland fire and to prevent structure fires from spreading to wildland fuels; regulates defensible space and provides ignition-resistant construction requirements to protect against fire exposure...

Guide providing engineering seismic design and building practices based on post-earthquake research.

Federal statistics about national energy consumption in residential homes.

Code set from IAPMO explaining plumbing standards. 2015 publication.

Guide describing the requirements by FORTIFIED Home™ for improving the home's resistance in severe thunderstorms, straight-line wind events, and high winds at the outer edges of tornadoes.

Report describing the results of a field study of five different ventilation system types in 29 homes in the Pacific Northwest.

Report describing testing and analysis on deep energy retrofits of existing single-family homes in the U.S.

Report describing how changing the air exchange rate of a home (the sum of the infiltration and mechanical ventilation airflow rates) affects the annual thermal conditioning energy.

Document describing three methods for elevating a home out of the flood zone.

The manual covers residential zoning issues - multiple, single-zone, and central multi-zone systems - and includes advice on working with homeowners to adapt the heating or cooling system design to meet modern home design features.

Case study on the design and evaluation of extended plate and beam, located in Mount Joy Pennsylvania.

Guide describing advanced framing, a system of construction framing techniques designed to optimize material usage and increase energy efficiency.

Fact sheet describing advanced framing techniques that reduce the amount of lumber used in constructing wood-framed houses while providing more space for wall insulation.

Report describing two retrofit duct sealing techniques - manually-applied sealants and injecting a spray sealant, that were implemented in several low-rise multi-unit buildings in North Carolina.

Case study about high humidity, mold and condensation on surfaces in S. Florida, and how building characteristics cause and amplify these problems.

This report describes research conducted to evaluate air transfer between the garage and living space in a single-family detached home constructed to the 2009 IECC by a production home builder in Maryland.

Case study examining the problem of unwanted air transfer from garage to living space and the effectiveness of garage exhaust ventilation or house supply ventilation to provide a solution to that.

Research report describing study of interior and exterior air sealing techniques to stop ice dams in five 1.5-story retrofit homes conducted by the NorthernSTAR Building America Partnership team run by University of Minnesota.

Report on adding insulation to load-bearing mass masonry buildings.

Report outlining workflow and results of regression models on monthly and daily utility data (meter readings of electricity consumption), outlining a process for screening and gathering useful results from inverse models.

Report analyzing design heating load sizing methods for superinsulated homes in cold climates and comparing them to the actual energy usage to determine if the building load calculation methodology should be changed for calculating the design heating load of these homes.

Guidance from HUD, EPA, NIH, and FEMA for workers who deal directly with asbestos.

This directory contains the I=B=R Ratings for cast-iron, steel, aluminum and copper boilers, baseboard and finned tube radiation, indirect-fired water heaters, effective as of the date of this publication.

Information sheet about reservoir claddings.

A book about structurally insulated panels.

Report presenting the building america research to market plan.

Web report explaining how correct filter sizing is an issue that applies to all new and existing homes that use ducted HVAC systems.

Document presenting some of the key technical properties of many of the most common building materials.

An online learning management resource for the construction community.

Article describing correct ways to eliminate water damage by incorporating a sacrificial layer to foundation walls and footings.

Information sheet with information about insulating and ventilating attics.

Case study about the grid integration of electrical vehicle supply equipment.

This is a guide for establishing smoke-free policies in public housing and multifamily properties.

News article from SFGate explaining and giving figures on how chimney failure is the most common type of damage to homes during an earthquake.

Report on the stability of furring strips as a means for cladding attachment over walls with thick exterior rigid insulation.

Article describing correct ways to attach rigid insulation to the exterior of commercial and residential buildings.

Report describing strategies to improve the aging steam heating systems in New York City to improve energy efficiency, reduce oil and gas usage, and cut maintenance costs.

Report on improving passive design adoption rates.

Report describing retrofitting options and methodology for architects, developers, and property owners to use when making decisions about retrofits for common building types in NY.