Library

Article describing moisture and ice dam issues in attics and how to air seal the attic floor.

Technical report describing the research and development of the Ventilation-Integrated Comfort System (VICS) which is a specifically designed, energy-efficient solution that seamlessly integrates with low-capacity, ducted heating, and cooling systems, offering controllable, balanced energy recovery...

A free tool used to calculate the required minimum flow rate of dwelling-unit ventilation.

IECC code note explaining new fan efficacy requirements, along with how to determine which fans are affected by the new fan requirements.

Report providing guidance on indoor air quality in single-family and multifamily housing for designers, builders, property managers, homeowners, buyers, and renters.

Document reviewing current and potential ventilation technologies for residential buildings with particular emphasis on North American climates and construction.

Report describing how to construct a frost protected shallow foundation (FPSF) as a practical alternative to a deeper, more-costly foundation in cold regions with seasonal ground freezing and the potential for frost heave.

Q&A article discussing how to address moisture issues in an attic in a wet and humid coastal climate.

Report on hybrid ventilation methods for insulated and sealed crawl spaces.

Report describing development of a package of energy efficiency measures to achieve 60% energy savings in a test house.

Fact sheet describing building envelope performance measures applicable to residential and small commercial construction.

Fact sheet describing field validations of a smart ventilation system to assess its effectiveness in assisting low-load homes in humid environments by maintaining acceptable indoor humidity conditions while ensuring adequate ventilation and indoor air quality.

Article describing building smoke control systems.

Standard that defines the roles of and minimum requirements for mechanical and natural ventilation systems and the building envelope intended to provide acceptable indoor air quality in low-rise residential buildings. This version of the standard was published in the year 2016, and is available for...

Standard that defines the roles of and minimum requirements for mechanical and natural ventilation systems and the building envelope intended to provide acceptable indoor air quality in low-rise residential buildings; published in the year 2019, and is available for preview and purchase at the...

Standard that describes the minimum requirements for residential buildings to achieve acceptable indoor air quality via dwelling-unit ventilation, local mechanical exhaust, and source control. This version of the standard was published in the year 2022, and is available for preview and purchase at...

This Standard provides a consistent, uniform methodology for evaluating the airtightness of building envelopes and heating and cooling air ducts and the air flows of mechanical ventilation systems.

Standard describing methods for testing the airtightness of buildings and HVAC equipment.

Test method that measures the capture efficiency of wall-mounted domestic range hoods under controlled conditions in a test chambers which available for preview and purchase at the link and was published in the year 2018.

Website providing information on all types of pest management for multi-family housing.

Research project evaluating the pre-and post-retrofit energy consumption of a marine climate retrofit, compare actual energy use to original predictions, and identify opportunities for cost savings in other similar retrofits in this climate.

Presentation on sustainable development including water conservation, passive solar, daylighting, natural ventilation, and land use.

Presentation by the Washington University in St. Louis Office of Sustainability on saving energy.

Presentation on urban land use and sustainable building design.

Presentation describing how to make a Corsi-Rosenthal Box for air cleaning.

Article describing a field study that test ventilation performance in nine homes and found current ventilation was inadequate to remove PM2.5 and CO2 levels; however, a directly exhausting range hood can reduce peak PM2.5 concentrations by 75% or more.

Paper that illustrates a performance check between the thermal performance of a Massive Insulating Concrete Form (ICF) wall system mocked up and Whole Building Performance criteria such as total space heating and cooling loads (thermal comfort).

Article about installing balanced ventilation systems.

Website providing consumer tips for using natural gas safely in the home, including guidance on cooking, fireplaces, ventilation, pilot lights, piping, etc.

Report presenting information that aids qualified architects and engineers in the identification of the best available refuge areas in existing buildings for sheltering in place during a tornado.

BSD-102 report providing guidance about whether to construct a vented or unvented attic based on hygro-thermal zone.

Information sheet with methods for constructing or retrofitting basements to reduce moisture issues.

Article describing the impact of increasingly stringent ventilation standards on multifamily buildings, highlighting the inefficiencies and challenges of exhaust-only ventilation in tightly sealed enclosures, the complications of achieving balanced ventilation, and the unintended consequences of...

Presentation describing the challenges of insulating an existing basement, presented to the Building America residential energy-efficiency stakeholder meeting.

This study uses a computer simulation approach to examine the energy and indoor air quality implications of passive and hybrid ventilation systems.

Document presenting analysis results, focusing on relative humidity (RH) excursions, which are defined as unique events of indoor RH above a threshold.

Preliminary results of two monitored lab homes constructed to represent the thermal characteristics of typical existing Florida homes are presented.

Building science report describing issues with vented attics in hot-humid climates and how sealed attic construction may be a solution.

A review on the knowledge about ventilated wall claddings from field performance and hydrothermal modeling.

Report describing the formation of icicles and ice dams along poorly ventilated roofs and how to mitigate ventilation issues with insulation and vents.

Information sheet about proper ventilation and air sealing.

Standard that defines the roles of and minimum requirements for mechanical and natural ventilation systems and the building envelope intended to provide acceptable indoor air quality in low-rise residential buildings. This version of the standard was published in the year 2010, and is available for...

Standard that defines the roles of and minimum requirements for mechanical and natural ventilation systems and the building envelope intended to provide acceptable indoor air quality in low-rise residential buildings. This version of the standard was published in the year 2013, and is available for...

This report examines indoor air quality in post-2013 homes across various climates, focusing on contaminant levels, ventilation equipment usage, and control measure impact, with regional data from Florida, Georgia, and South Carolina.

ENERGY STAR overview on certified ventilation fans.

Standard that provides procedures and methods for meeting minimum ventilation and indoor air quality requirements to engineers, design professionals, owners, and jurisdictional authorities where model codes have been adopted. This is the current version of the standard, which was published in the...

Report describing the use of attic ventilation to control moisture in cathedral roofs and avoid the formation of ice dams.

Report describing a field study of 31 homes to test envelope and duct leakage and fan flowrates, and to determine ventilation operation characteristics.

Fact sheet describing how weatherstripping can be an easy and cost-effective way to save money on energy costs and improve comfort by reducing drafts.

An article describing a way to protect drain and ventilation holes in brick veneer siding against pests. Selecting a fine screen mesh opening (1/55-inch or 0.5-mm) is important to guard against small insects such as subterranean termites.