Library

Article describing vapor retarder requirements in the International Residential Code and International Building Code 2021.

Article describing methods for venting a vented attic and a roof assembly over an unvented attic.

Standards book discussing the minimum standards of total system balance of HVAC systems.

Standard covering equipment sizing loads for single-family-detached homes, small multi-unit structures, condo­miniums, town houses and manufactured homes.

Technical manual from ACCA outlining correct methods for zoning of residential HVAC systems.

Report examining the structural properties and applications of an innovative studless building system, detailing its testing regime and providing an engineering guide for architects and engineers.

Fact sheet poster describing how to add exterior, continuous, rigid insulation to the exterior walls when replacing siding on an existing home.

Report on the design and evaluation of extended plate and beam.

Case study on the design and evaluation of extended plate and beam, located in Mount Joy Pennsylvania.

Article about different types of weather resistant barrier.

Report analyzing design heating load sizing methods for superinsulated homes in cold climates and comparing them to the actual energy usage to determine if the building load calculation methodology should be changed for calculating the design heating load of these homes.

Technical fact sheet describing ways to construct asphalt shingle roofs to be more resistant to high winds and hurricanes; also published in FEMA P-499 “Home Builder’s Guide to Coastal Construction: Technical Fact Sheet Series.”

Code establishing the rules of safety relating only to pressure integrity for the design, fabrication, and inspection of boilers and pressure vessels during construction which was published in the year 2017 and is available to order at the referenced link.

Code establishing the rules of safety relating only to pressure integrity for the design, fabrication, and inspection of boilers and pressure vessels during construction which was published in the year 2021 and is available to order at the referenced link.

Web based tool providing decision-making guidance for selecting wall assembly components.

Article describing the control layers (air, thermal, and vapor barriers) needed to build homes successfully in very cold locations.

Training manual on how to locate ducts within conditioned space and compact design.

Information sheet discussing how OSB will define the future of the structural sheathing market. OSB will define the future of the structural sheathing market. - See more at: http://bct.eco.umass.edu/publications/by-title/choosing-between-oriented-strandboard-and-plywood/#sthash.RilEtDpl.dpuf

Article describing correct ways to attach rigid insulation to the exterior of commercial and residential buildings.

Report describing strategies to improve the aging steam heating systems in New York City to improve energy efficiency, reduce oil and gas usage, and cut maintenance costs.

Document presenting step-by-step process for installing rigid insulating sheathing over wood studs or house wrap.

Report outlining the issues with using existing ducts with a new low-load HVAC system, which reduces throw at supply registers causing decreased mixing of supply and room air, leading to potential thermal comfort complaints.

Report on high-R wall design called extended plate and beam that uses foam sheathing insulation with wall framing.

Information sheet about what length screws should be used, and how closely to space the screws when fastening furring strips to a foam-sheathed wall.

Factsheet describing ways to install sheathing over existing 1x roof decking.

Checklist describing requirements for roof sheathing along the gable end truss or rafter to achive a FORTIFIED Roof, including New Roof designations and exceptions.

Checklist highlighting key concepts of wind design uplift pressures and design uplift pressure ratings for proper selection and installation of residential roof covering systems to comply with section R905.1 of the 2015 International Residential Code for a FORTIFIED Roof™–New Roof designation.

Checklist providing selection and installation guidance for residential, non-structural metal roof systems installed over wood roof decks with a roof slope 2:12 or greater to comply with section R905.1 of the 2015 IRC for a FORTIFIED Roof – New Roof Designation.

Checklist providing additional guidance and options for asphalt shingle installations at roof edges, intersections and valleys.

Website offering an online training that teaches disaster-resistant best practices for roofers.

Document that gives a step-by-step approach for designing attachments for cladding materials through foam sheathing.

Correcting pressure imbalances in your HVAC system can result in a healthier, more efficient home.

Research study describing the impact resistance performance of advanced framed wall systems with insulating sheathing as the primary sheathing from wind blown debris.

Central return designs require an open pathway between the room and the heart of the house where the return grill is located.

Article showing steps for kick out flashing at roof-wall intersection.

Standard technical manual with information about HVAC balancing, testing air and hydronic systems.

Siding installation guide for Ply Gem Siding Group products.

Case study about how to properly tape insulating sheathing drainage planes.

Discussion of building sheathing.

Report providing extensive guidance on controlling moisture in building envelopes through proper selection and installation on air, water, thermal, and vapor barriers.

Report covering wind loading on roofing assemblies.

Fact sheet describing proper roof sheathing installation and illustrating fastening methods that will enhance the durability of a building in high-wind areas; also published in FEMA P-499 “Home Builder’s Guide to Coastal Construction: Technical Fact Sheet Series.”

Guide describing the installation of windows in walls that have foam plastic insulating; guide provides several methods for attaching, supporting, and flashing windows in walls with rigid foam sheathing. (Note: The link only goes to the table of contents for the guide, the full guide can be...

Conference paper describing testing of the performance of fasteners used to attach rigid foam insulation to the exterior of walls.

Information sheet describing correct application of stucco.

Discussion of building sheathing.

Webpage describing the standards, seminars, exams, etc regarding testing, adjusting and balancing (TAB).

Article about installing balanced ventilation systems.

Report on a project conducted to better understand the current usage of thermostatic radiator valves by key market players in steam and hot water heating and to conduct limited experiments on the effectiveness of new and old thermostatic radiator valves as a means of controlling space temperatures...

Article describing the evolution of the IRC to permit class 3 vapor retarders (latex paint) in walls coupled with exterior continuous insulation to allow drying and reduce condensation risk.