Library

Code describing energy codes for energy-conserving and compliant designs in Florida.

Report providing builders in marine climates with guidance for building homes that have whole-house energy savings of 40% over the Building America benchmark with no added overall costs for consumers.

Article describing methods for thermally isolating a garage in a Passive House-certified multifamily building.

Standards book discussing the minimum standards of total system balance of HVAC systems.

Document describing three methods for elevating a home out of the flood zone.

Vinyl siding estimating and installation guide for vinyl siding products.

Radiant, hydronics, geothermal -- they are a vital part of modern comfort and energy solutions. ACCA helps hydronics contractors operate at peak performance.

Standard covering equipment sizing loads for single-family-detached homes, small multi-unit structures, condo­miniums, town houses and manufactured homes.

Technical manual from ACCA outlining correct methods for zoning of residential HVAC systems.

Guide describing advanced framing, a system of construction framing techniques designed to optimize material usage and increase energy efficiency.

Report analyzing design heating load sizing methods for superinsulated homes in cold climates and comparing them to the actual energy usage to determine if the building load calculation methodology should be changed for calculating the design heating load of these homes.

This Best Practices Manual is the product of Hammer & Hand’s ongoing work to document and internally codify our standard operating procedures for construction practice.

Code establishing the rules of safety relating only to pressure integrity for the design, fabrication, and inspection of boilers and pressure vessels during construction which was published in the year 2017 and is available to order at the referenced link.

Code establishing the rules of safety relating only to pressure integrity for the design, fabrication, and inspection of boilers and pressure vessels during construction which was published in the year 2021 and is available to order at the referenced link.

Article Describing methods for thermally isolating multifamily parking garages.

The Builder's Guide provides the building industry with the latest and best practical information on how to apply building science principles to structures as systems in hot-humid climate regions.

Document providing guidance to U.S. home builders who want to accept the challenge.

Guide describing measures that builders in the cold and very cold climates can take to build homes that have whole-house energy savings of 40% over the Building America benchmark with no added overall costs for consumers.

Guidance document providing BA research teams and partners with specific information and approaches to identifying and overcoming potential barriers to Building America (BA) innovations arising in and/or stemming from codes, standards, and rating methods.

Report summarizing research results for the 30% energy savings level and demonstrates that lead builders can successfully provide 30% homes in the Marine Climate Region on a cost-neutral basis.

Website providing CAD files and drawings of advanced framing details.

Document detailing how to build radon-resistant homes.

Document outlining building science principles about air flow, heat flow and moisture flow in homes.

Training manual on how to locate ducts within conditioned space and compact design.

An article discussing how different metal roof materials and attachment methods affect the ability of the roof to thermally expand and contract and the durability of different solutions.

Report on the stability of furring strips as a means for cladding attachment over walls with thick exterior rigid insulation.

Report describing strategies to improve the aging steam heating systems in New York City to improve energy efficiency, reduce oil and gas usage, and cut maintenance costs.

Research study investigating the energy performance and cost effectiveness of several state-of-the-art retrofit strategies that could be used in residential houses in the Boston and New England area.

Report outlining the steps developers can take to create high-performance standards on a community-wide scale.

Part I of the Guide addresses walls constructed with 2x6 wood frame studs, wood structural panel (WSP) sheathing as exterior sheathing, gypsum board as interior sheathing, and a cladding system installed over WSP sheathing in low-rise residential buildings up to three stories in height. Walls with...

The Guide addresses walls constructed with 2x4 wood frame studs, wood structural panel sheathing (WSP) as wall bracing and added backing for foam sheathing, a layer of rigid foam sheathing insulation up to 1.5 inches thick over the WSP, and a cladding system installed over the foam sheathing in low...

Part I of the Guide addresses walls constructed with 2x6 wood frame studs, wood structural panel (WSP) sheathing as exterior sheathing, gypsum board as interior sheathing, and a cladding system installed over WSP sheathing in low-rise residential buildings up to three stories in height.

Website providing building science based guidance and training for residential construction.

Article describing research encouraging use of exterior insulation to warm interior sheathing surfaces in walls and roof assemblies to reduce the likelihood of condensation during cold weather

Report focusing on building envelopes that have been enhanced with phase change materials (PCMs), which can simultaneously reduce total cooling loads and shift peak-hour loads.

Job Process sheet for the manufactured housing industry showing how to cut insulation batts to fit wall cavities in a factory production environment.

Guidance document on deep energy retrofits.

Part of a larger LBNL report (Deep Energy Retrofit Guidance for the Building America Solutions Center), the Design and Construction Process chapter provides detailed guidance for each process phase: pre-planning, planning, construction, test-out and post-occupancy.

Part of a larger LBNL report (Deep Energy Retrofit Guidance for the Building America Solutions Center), the Lessons Learned chapter focuses on successful deep energy retrofit projects throughout the U.S.

Part of a larger LBNL report (Deep Energy Retrofit Guidance for the Building America Solutions Center), the Occupant Behavior chapter discusses how to assess homeowner behavior patterns and use these patterns to enhance overall energy savings.

Part of a larger LBNL report (Deep Energy Retrofit Guidance for the Building America Solutions Center), the Reducing costs and Increasing Cost-Effectiveness chapter provides suggestions for controlling deep retrofit costs, including both 'do's' and 'don'ts'.

Report outlining the issues with using existing ducts with a new low-load HVAC system, which reduces throw at supply registers causing decreased mixing of supply and room air, leading to potential thermal comfort complaints.

Information about dense pack, cellulose insulation.

The objective of this research was to quantify the field performance of wood-frame walls clad with a variety of common claddings in a mixed-humid climate.

Report on problems and solutions with EIFS stucco wall cladding systems.

Discussion of structural thermal resistance.

Website from the U.S. Department of Energy providing consumers with information on saving energy and using renewable energy technologies.

Information sheet with details on a building enclosure designed for Albuquerque, NM, as an example for building enclosures built for hot-dry and mixed-dry climates.

Information sheet that summarizes Insulated Concrete Form (ICF) construction including advantages and disadvantages of this construction strategy.

Report on the field evaluation of whole-building approaches and estimation of the relative contributions of select technologies toward reducing energy use related to space conditioning in new manufactured homes.