Library

2009 edition of code establishing a baseline for the design and installation of fuel gas systems and gas fired appliances through performance requirements.

Code set from IAPMO explaining plumbing standards. 2012 Publication.

2015 edition of code establishing a baseline for the design and installation of fuel gas systems and gas fired appliances through performance requirements.

Code set from IAPMO explaining plumbing standards. 2015 publication.

2018 edition of code establishing a baseline for the design and installation of fuel gas systems and gas fired appliances through performance requirements.

Federal statistics about national energy consumption in residential homes in 2020

Article describing vapor retarder requirements in the International Residential Code and International Building Code 2021.

Article describing products that can enhance the efficiency and safety of clothes dryer vents.

Report providing builders in the hot-dry and mixed-dry climates with guidance for building homes that have whole-house energy savings of 40% over the Building America benchmark with no added overall costs for consumers.

Article describing thermal bridging, construction practices that encourage thermal bridging, and solutions.

Guide for homeowners describing how to find and seal basement and attic air leaks, determine if attic insulation is adequate, make improvements safely, and reduce energy bills.

Report describing testing and analysis on deep energy retrofits of existing single-family homes in the U.S.

Article describing methods for thermally isolating a garage in a Passive House-certified multifamily building.

Information sheet about unvented fireplaces and combustion safety.

Standards book discussing the minimum standards of total system balance of HVAC systems.

Standard covering equipment sizing loads for single-family-detached homes, small multi-unit structures, condo­miniums, town houses and manufactured homes.

Technical manual from ACCA outlining correct methods for zoning of residential HVAC systems.

Fact sheet poster describing how to add exterior, continuous, rigid insulation to the exterior walls when replacing siding on an existing home.

Technical report describing the SPS (Structural Panel System), an innovative implementation of the "perfect wall" concept, situating environmental control layers on the exterior side of structural components for improved constructability, cost-effectiveness, and performance, validated through the...

Website providing research, efficiency and safety standards development, and advocacy to the home appliance industry to bring efficient, high-performing home appliances to consumers.

Website reporting efficiencies for dehumidifiers, room air conditioners, and room air cleaners that are tested by independent laboratories and reported by the Association of Home Appliance Manufacturers.

Website article interviewing the inventor of the Larsen truss, a history of its use, and a discussion of its advantages and disadvantages.

Article about different types of weather resistant barrier.

Report providing information regarding the benefits and challenges associated with the installation of earthquake-actuated automatic shut-off valves (ASVs) or remote-control valves (RCVs) to stop the flow of natural gas into buildings in the event of an earthquake or rupture of the gas line.

Report with updated energy consumption data for 28 residential & commercial miscellaneous electric loads (MELs), including projections to 2040.

Report that collected field data from a whole-home program in Illinois are utilized to compare marketplace-installed measures to the energy saving optimal packages previously developed for 15 housing types.

Report on adding insulation to load-bearing mass masonry buildings.

Report analyzing design heating load sizing methods for superinsulated homes in cold climates and comparing them to the actual energy usage to determine if the building load calculation methodology should be changed for calculating the design heating load of these homes.

Safety brochure from the Consumer Product Safety Commission (CPSC) describing the dangers to children of furniture tipping over if it is not securely anchored.

Website providing consumers with information about the risk to children from appliances and furniture tipping over and ways to anchor furniture and appliances to prevent this hazard.

Webpage describing different types of appliance thermometers, how they work, and how they should be used by homeowners.

Report about a building project in the marine climate.

Technical report describing the thermal performance of 40 common building envelope details for mid- and high-rise buildings, including analyses to optimize energy efficiency and reduce thermal bridging.

Report focused on foundation insulation R-values for cold climates and the design, construction, and performance implications.

The exhaust from residential combustion appliances contains air pollutants and high levels of moisture that must be conveyed to the outdoors to maintain acceptable indoor quality.

A basic guide walking through the various types of valves useful in mitigating the effects of earthquakes and other seismic events on natural gas pipelines for residential use.

Report about a project that examines implementation of advanced retrofit measures in the context of a large-scale weatherization program and the archetypal Chicago, Illinois, brick bungalow.

This report outlines research activities that are expected to facilitate the adoption of energy retrofits by remodeling contractors and roofing contractors using retrofit panels which applicable to many existing house designs in most climates and markets.

Article describing the building science implications of insulating vented or unvented attics.

Article describing the research into insulating vented versus unvented attics.

SPFA website signup page to access SPFA documents.

Report describing approaches to insulating basements in homes built to meet Energy Star levels of performance of heat loss reduction.

Information sheet describing techniques for insulating basements.

Report summarizing commissioning, short-term testing, utility bill data analysis, and results of on-site monitoring of a deep energy retrofit.

Code establishing the rules of safety relating only to pressure integrity for the design, fabrication, and inspection of boilers and pressure vessels during construction which was published in the year 2017 and is available to order at the referenced link.

Code establishing the rules of safety relating only to pressure integrity for the design, fabrication, and inspection of boilers and pressure vessels during construction which was published in the year 2021 and is available to order at the referenced link.

Brochure explaining the essential basis for advanced framing and some of the more common advanced framing details.

Information sheet about insulating slabs.

Information sheet providing recommendations on the installation of vapor control layers.

Article describing selecting insulation for minimizing condensation risks.