Library

2009 edition of code establishing a baseline for energy efficiency by setting performance standards for the building envelope (defined as the boundary that separates heated/cooled air from unconditioned, outside air), mechanical systems, lighting systems and service water heating systems in homes...

2009 edition of code establishing a baseline for existing building retrofits to reach appropriate safety levels under new construction requirements covered in other ICC codes.

Fact sheet describing a report providing best practices for reducing damages from floods to manufactured homes.

Building code for the state of Florida.

2012 edition of code establishing a baseline for energy efficiency by setting performance standards for the building envelope (defined as the boundary that separates heated/cooled air from unconditioned, outside air), mechanical systems, lighting systems and service water heating systems in homes...

2012 edition of code establishing a baseline for existing building retrofits to reach appropriate safety levels under new construction requirements covered in other ICC codes.

2012 edition of code establishing a baseline for the design and installation of fuel gas systems and gas fired appliances through performance requirements.

2012 edition of code for residential buildings that creates minimum regulations for one- and two-family dwellings of three stories or less, bringing together all building, plumbing, mechanical, fuel gas, energy and electrical provisions for one- and two-family residences.

Report describing practices and considerationsfor more efficient water use in pools, spas, and fountains.

2015 edition of code for commercial buildings that brings together all structural, plumbing, mechanical, fuel gas, energy and electrical provisions for all buildings except detached one- and two-family residences and townhouses up to three stories.

2015 edition of code establishing a baseline for energy efficiency by setting performance standards for the building envelope (defined as the boundary that separates heated/cooled air from unconditioned, outside air), mechanical systems, lighting systems and service water heating systems in homes...

2015 edition of code establishing a baseline for existing building retrofits to reach appropriate safety levels under new construction requirements covered in other ICC codes.

2015 edition of code establishing minimum regulations for mechanical systems, including heating, cooling, ventilation, exhaust, ducts, fireplaces, combustion and hydronic systems, using prescriptive and performance-related provisions.

2015 edition of code for residential buildings that creates minimum regulations for one- and two-family dwellings of three stories or less, bringing together all building, plumbing, mechanical, fuel gas, energy and electrical provisions for one- and two-family residences.

Federal statistics about national energy consumption in residential homes.

Fact sheet providing an overview of FEMA P-348, Protecting Building Utility Systems From Flood Damage.

Document describing portions of the flood provisions from the 2018 editions of the IBC, IRC, IEBC, IMC, IPC, IFGC, IFC, ISPSC, IPSDC, and ICC Performance Code.

2018 edition of code establishing a baseline for energy efficiency by setting performance standards for the building envelope (defined as the boundary that separates heated/cooled air from unconditioned, outside air), mechanical systems, lighting systems and service water heating systems in homes...

2018 edition of code establishing a baseline for existing building retrofits to reach appropriate safety levels under new construction requirements covered in other ICC codes.

2018 edition of code establishing minimum regulations for mechanical systems, including heating, cooling, ventilation, exhaust, ducts, fireplaces, combustion and hydronic systems, using prescriptive and performance-related provisions.

2018 edition of code for residential buildings that creates minimum regulations for one- and two-family dwellings of three stories or less, bringing together all building, plumbing, mechanical, fuel gas, energy and electrical provisions for one- and two-family residences.

Guidebook covering basic principles and data used in the HVAC&R industry. This is the 2021 edition of the handbook, which can be purchased physically or digitally at the reference link in versions using either I-P units of measurement or SI units of measurement.

2021 edition of code establishing a baseline for existing building retrofits to reach appropriate safety levels under new construction requirements covered in other ICC codes.

Catalog describing FEMA preparedness seminars from 2021 including preparedness and natural hazards topics.

Article describing products that can enhance the efficiency and safety of clothes dryer vents.

Guide providing information for homeowners and renters on how to clean up residential mold problems and how to prevent mold growth.

Report telling consumers the risks of radon, how radon gets into a home, and steps consumers can take to reduce radon exposure in their homes.

Document describing advancement in factory built housing innovations.

Report describing testing and analysis on deep energy retrofits of existing single-family homes in the U.S.

Guidance document from the UN environment programme on climate-resilient buildings and communities practices, including guidance on heat waves, drought, hurricanes, and flooding.

Report describing how changing the air exchange rate of a home (the sum of the infiltration and mechanical ventilation airflow rates) affects the annual thermal conditioning energy.

Information sheet about unvented fireplaces and combustion safety.

Standards book discussing the minimum standards of total system balance of HVAC systems.

Standard providing master specifications for closed cell, medium density spray polyurethane foam air barriers located in the non-accessible part of the wall.

Standard outlining materials and installation methods by using commercial building wraps.

Document describing three methods for elevating a home out of the flood zone.

Standard covering equipment sizing loads for single-family-detached homes, small multi-unit structures, condo­miniums, town houses and manufactured homes.

The manual covers residential zoning issues - multiple, single-zone, and central multi-zone systems - and includes advice on working with homeowners to adapt the heating or cooling system design to meet modern home design features.

Technical manual from ACCA outlining correct methods for zoning of residential HVAC systems.

This Standard establishes the minimum requirements to evaluate a residence with regards to energy efficiency, water conservation, occupant comfort, and indoor air quality.

Standard providing nationally recognized, manufacturer-endorsed set of inspection tasks for HVAC maintenance.

Standard providing a universally accepted definition for quality installation for residential and commercial heating, ventilating, and air conditioning applications.

Document detailing the requirements, roles, and obligations for participants in an organized effort, ensuring that HVAC installations comply with the ANSI/ACCA 5 QI – 2010 (HVAC Quality Installation Specification) QI Standard.

Report providing guidance on wet floodproofing crawlspaces, unfinished basements, and garages.

Report providing guidance to homeowners and business owners on protecting crawlspaces from flood damage.

Standard for use and reference by designers, architects, engineers, contractors, installers and users for evaluating, selecting, specifying and properly installing flexible duct in heating and air conditioning systems.

Guide describing advanced framing, a system of construction framing techniques designed to optimize material usage and increase energy efficiency.

Report investigating implemention of advanced power strips for entertainment and home office electronics would reduce energy consumption across the residential market.

Report describing the experience gained from AIA’s Disaster Assistance Program with first-hand accounts of disaster response and recovery, case studies and other best practices, including approaches to designing buildings to be more adaptable to uncertainty.

Document reporting results from a study done to evaluate effects of automotive emissions from attached garages on the indoor environment.