Library

Standard using deficiency-based and systematic procedures that use performance-based principles to evaluate and retrofit existing buildings to withstand the effects of earthquakes.

Standard using deficiency-based and systematic procedures that use performance-based principles to evaluate and retrofit existing buildings to withstand the effects of earthquakes. The current version of this standard was published in the year 2017, and is available in both digital and print...

Fact sheet for natural gas customers describing city’s seismic gas shut-off valve requirements.

Reports describing a mathematical methodology for assessing the seismic performance of buildings.

Report promoting public safety and welfare by reducing the risk of earthquake-induced damage to existing homes.

Report promoting public safety and welfare by reducing the risk of earthquake-induced damage to existing homes.

Report providing retrofit measures intended to significantly reduce damage and increase occupant safety for existing buildings.

Report seeking to teach building contractors and building inspectors the correct methods for doing typical seismic retrofits that have been designed by an engineer or architect or described in a prescriptive standard.

Newsletter containing five articles focused on seismic retrofitting.

Article outlining the key issues related to the protection of the building envelope against seismic forces.

Description of California Senate Bill SB 1898, which requires the sale of new seismic gas shutoff devices sold in California to be certified by the State Architect.

Fact sheet describing guidance concerning lot selection and building siting considerations for coastal residential buildings, including factors that constrain siting decisions, coastal setback lines, common siting problems, and suggestions for builders, designers, and owners; also published in FEMA...

Report from FEMA describing techniques for floodproofing structures.

Report summarizing commissioning, short-term testing, and analysis that occurred before, during, and just after the actual retrofit of the Bay Ridge project.

Report evaluating the renovation of a 5,800-ft2, multiuse facility located in St. Petersburg, on the west coast of central Florida, in the hot-humid climate.

Website with consumer information about duct cleaning.

Report comparing the performance of seven differing types of residential water heating systems in a side-by-side test configuration over a full year period.

Document about testing of seven water heating systems in the Hot Water Systems laboratory in central Florida.

High-density sidewall cavity insulation can be a major comfort and savings boost. It saves energy by slowing both conductive and convective losses, but only if the right things are done and done right. This always requires site-specific thinking.

Paper describing the development and testing of an affordable net-zero energy house in Lenoir City, Tennessee.

Website providing consumers with resources to find, select and install heat pump water heaters.

Initiatives of smoke-free housing policies in New York State.

Toolkits for residents and owner/managers who live and work in federally assisted housing.

Guidelines to assist builders in designing and constructing homes equipped with a set of features that make the installation of solar energy systems after the completion of the home’s construction easier and less expensive.

Report identifying the important aspects of building design and construction to enable installation of solar photovoltaic and heating systems at some time after the building is constructed.

Website describing how solar water heaters -- also called solar domestic hot water systems -- can be a cost-effective way to generate hot water for your home.

The RERH specifications and checklists take a builder and a project design team through the steps of assessing a home’s solar resource potential and defining the minimum structural and system components needed to support a solar energy system.

Specifications to assist builders in designing and constructing homes equipped with a set of features that make the installation of solar energy systems after the completion of the home’s construction easier and less expensive.

Research study presenting a unique opportunity to both identify and evaluate deep retrofit measures that are practical and potentially cost effective for the retrofit market, as well as review the cost effectiveness of the Passive House design approach for achieving energy savings in deep retrofits.

Proposed HVAC filter labeling standard and underlying analysis by the California Energy Commission.

Standard that defines the roles of and minimum requirements for mechanical and natural ventilation systems and the building envelope intended to provide acceptable indoor air quality in low-rise residential buildings. This version of the standard was published in the year 2016, and is available for...

Standard 680 establishes definitions, classifications, test requirements, data requirements, ratings, operating requirements, marking and nameplate data and conformance conditions for residential air filter equipment.

This Standard provides a consistent, uniform methodology for evaluating the airtightness of building envelopes and heating and cooling air ducts and the air flows of mechanical ventilation systems.

Guide providing guidance on conducting seismic risk assessments for buildings. The link goes to the current version of this standard, which was published in the year 2016 and is available for preview and purchase. Previous editions of this standard were published in the year 2016, 2007, and 1999...

Standard covering the installation of fenestration products in new and existing construction, which was published in the year 2019, and is available for preview and purchase at the referenced link.

Standard covering the installation of fenestration products in new and existing construction which was published in the year 2007, and is available for preview and purchase at the referenced link.

Standard describing methods for installing radon mitigation systems in existing residential buildings three stories or less in height which was published in the year 2021 and is available for preview and purchase at the reference link.

Practice providing a guide or standard to undertake seismic risk assessment of properties. The current version of the standard was published in the year 2016 and is available for preview and purchase at the link. Previous versions of the standard were published in the years 2016 and 2007, and are...

Detailed requirements for testing, exposure modeling, and allowable limits for modeled indoor air concentrations.

Specification covering the standard requirements for application of full thickness Portland cement-based plaster for exterior (stucco) and interior work. This standard was produced in the year 2022, and is available for preview and purchase at the reference link. There are also other versions of...

Specification covering the standard requirements for application of full thickness Portland cement-based plaster for exterior (stucco) and interior work. This standard was produced in the year 2023, and is available for preview and purchase at the reference link. There are also other versions of...

Standard specification covering elastomeric cellular preformed gasket and sealing materials. This version of the standard was published in the year 2011 and is available for preview and purchase at the reference link. Other versions of the standard were published in the years 2021, 2015, 2006, and...

Standard specification covering elastomeric cellular preformed gasket and sealing materials. This version of the standard was published in the year 2021 and is available for preview and purchase at the reference link. Other versions of the standard were published in the years 2015, 2011, 2006, and...

Standard specification covering the properties of a cured single- or multicomponent cold-applied elastomeric joint sealant for sealing, caulking, or glazing operations on buildings, plazas, and decks for vehicular or pedestrian use, and types of construction other than highway and airfield pavements...

Test method designed to calculate an assigned air permeance of flexible sheet or rigid panel-type materials at a reference air pressure differential of 75 Pa which was published in the year 2021 and is available for preview and purchase at the reference link.

Standard describing a test method measuring air-leakage rates through a building envelope under controlled pressurization and de-pressurization which was published in the year 2019 and is available for preview and purchase at the reference link.

Test method providing a rapid means of determining the steady-state thermal transmission properties of thermal insulations and other materials with a high level of accuracy when the apparatus has been calibrated appropriately. This version of the standard was published in the year 2021 and is...

Test method designed to obtain reliable values for the WVTR of plastic film and sheeting which was published in the year 2020 and is available for preview and purchase at the reference link.

Standard describing two techniques for measuring air leakage rates through a building envelope in buildings that may be configured to a single zone which was published in the year 2022 and is available for preview and purchase at the reference link.

Report addressing barriers to information, contractor resources and cost savings associated with steam balancing multifamily buildings.