Library

Article describing vapor retarder requirements in the International Residential Code and International Building Code 2021.

Report providing builders in marine climates with guidance for building homes that have whole-house energy savings of 40% over the Building America benchmark with no added overall costs for consumers.

Article describing methods for venting a vented attic and a roof assembly over an unvented attic.

Document describing three methods for elevating a home out of the flood zone.

Report examining the structural properties and applications of an innovative studless building system, detailing its testing regime and providing an engineering guide for architects and engineers.

Fact sheet poster describing how to add exterior, continuous, rigid insulation to the exterior walls when replacing siding on an existing home.

Report on the design and evaluation of extended plate and beam.

Case study on the design and evaluation of extended plate and beam, located in Mount Joy Pennsylvania.

Article about different types of weather resistant barrier.

Technical fact sheet describing ways to construct asphalt shingle roofs to be more resistant to high winds and hurricanes; also published in FEMA P-499 “Home Builder’s Guide to Coastal Construction: Technical Fact Sheet Series.”

This Best Practices Manual is the product of Hammer & Hand’s ongoing work to document and internally codify our standard operating procedures for construction practice.

Document providing guidance to U.S. home builders who want to accept the challenge.

Guide describing measures that builders in the cold and very cold climates can take to build homes that have whole-house energy savings of 40% over the Building America benchmark with no added overall costs for consumers.

Web based tool providing decision-making guidance for selecting wall assembly components.

Guidance document providing BA research teams and partners with specific information and approaches to identifying and overcoming potential barriers to Building America (BA) innovations arising in and/or stemming from codes, standards, and rating methods.

Report summarizing research results for the 30% energy savings level and demonstrates that lead builders can successfully provide 30% homes in the Marine Climate Region on a cost-neutral basis.

Article describing the control layers (air, thermal, and vapor barriers) needed to build homes successfully in very cold locations.

Document detailing how to build radon-resistant homes.

Information sheet discussing how OSB will define the future of the structural sheathing market. OSB will define the future of the structural sheathing market. - See more at: http://bct.eco.umass.edu/publications/by-title/choosing-between-oriented-strandboard-and-plywood/#sthash.RilEtDpl.dpuf

Article describing correct ways to attach rigid insulation to the exterior of commercial and residential buildings.

Report outlining the steps developers can take to create high-performance standards on a community-wide scale.

Document presenting step-by-step process for installing rigid insulating sheathing over wood studs or house wrap.

Part of a larger LBNL report (Deep Energy Retrofit Guidance for the Building America Solutions Center), the Design and Construction Process chapter provides detailed guidance for each process phase: pre-planning, planning, construction, test-out and post-occupancy.

Part of a larger LBNL report (Deep Energy Retrofit Guidance for the Building America Solutions Center), the Lessons Learned chapter focuses on successful deep energy retrofit projects throughout the U.S.

Part of a larger LBNL report (Deep Energy Retrofit Guidance for the Building America Solutions Center), the Occupant Behavior chapter discusses how to assess homeowner behavior patterns and use these patterns to enhance overall energy savings.

Part of a larger LBNL report (Deep Energy Retrofit Guidance for the Building America Solutions Center), the Reducing costs and Increasing Cost-Effectiveness chapter provides suggestions for controlling deep retrofit costs, including both 'do's' and 'don'ts'.

Report on high-R wall design called extended plate and beam that uses foam sheathing insulation with wall framing.

Information sheet about what length screws should be used, and how closely to space the screws when fastening furring strips to a foam-sheathed wall.

Factsheet describing ways to install sheathing over existing 1x roof decking.

Checklist describing requirements for roof sheathing along the gable end truss or rafter to achive a FORTIFIED Roof, including New Roof designations and exceptions.

Checklist highlighting key concepts of wind design uplift pressures and design uplift pressure ratings for proper selection and installation of residential roof covering systems to comply with section R905.1 of the 2015 International Residential Code for a FORTIFIED Roof™–New Roof designation.

Checklist providing selection and installation guidance for residential, non-structural metal roof systems installed over wood roof decks with a roof slope 2:12 or greater to comply with section R905.1 of the 2015 IRC for a FORTIFIED Roof – New Roof Designation.

Checklist providing additional guidance and options for asphalt shingle installations at roof edges, intersections and valleys.

Website offering an online training that teaches disaster-resistant best practices for roofers.

Document that gives a step-by-step approach for designing attachments for cladding materials through foam sheathing.

Website blog with guidance about calculating heat-loss.

Research study describing the impact resistance performance of advanced framed wall systems with insulating sheathing as the primary sheathing from wind blown debris.

Article showing steps for kick out flashing at roof-wall intersection.

Article describing the flashing of roofs and what to look for, targeted at home inspectors.

Siding installation guide for Ply Gem Siding Group products.

Case study about how to properly tape insulating sheathing drainage planes.

Discussion of building sheathing.

Report providing extensive guidance on controlling moisture in building envelopes through proper selection and installation on air, water, thermal, and vapor barriers.

Article describing mulching with lawn clippings.

Report discussing development of scopes of work and quality management for builders in mixed-humid climates.

Report investigating what motivates remodelers to become energy-focused and what technical knowledge that need to be energy-focused.

Report covering wind loading on roofing assemblies.

Report presenting ways public housing authorities (PHAs) can develop packages of energy efficiency retrofit measures the PHAs can cost-effectively implement with their own staff in the normal course of housing operations at the time when units are refurbished between occupancies.

Report designed to help a builder understand quality management and its role in transitioning from conventional to HPH building and remodeling.

Fact sheet describing proper roof sheathing installation and illustrating fastening methods that will enhance the durability of a building in high-wind areas; also published in FEMA P-499 “Home Builder’s Guide to Coastal Construction: Technical Fact Sheet Series.”