Library

Article describing vapor retarder requirements in the International Residential Code and International Building Code 2021.

Article describing methods for venting a vented attic and a roof assembly over an unvented attic.

Article describing utility rates, net metering policies, installation costs, financial incentives, and other info for both consumers who are interested in installing renewable energy systems and for energy justice and clean energy advocates.

Fact sheet describing best strategies to bring ductwork on single-story homes with a slab-on-grade foundation in hot, dry climates into the conditioned envelope of the home intending to highlight the pros and cons of multiple ductwork integration strategies, including traditional duct systems in...

The research report outlines a practical and cost-effective strategy utilizing central HVAC systems to optimize humidity control and ventilation in energy-efficient homes located in hot-humid climates, demonstrating significant improvements without requiring complex equipment upgrades.

Article describing recessed lighting, which if installed incorrectly may contribute to air leakage and compromise building envelope efficiency.

Article about different types of weather resistant barrier.

Technical report describing how the FSEC Energy Research Center explores low-cost space-conditioning upgrades for existing homes by integrating centrally located, high-efficiency ductless mini split heat pumps with older but functional central space conditioning systems, aiming to achieve energy...

Technical fact sheet describing ways to construct asphalt shingle roofs to be more resistant to high winds and hurricanes; also published in FEMA P-499 “Home Builder’s Guide to Coastal Construction: Technical Fact Sheet Series.”

Report describing the business case of hosting a Level 2 electric vehicle (EV) charging station in New York, including analysis of real-world data on equipment use, costs, revenue, and assumptions derived from industry reports and original research.

Report describing approaches to insulating basements in homes built to meet Energy Star levels of performance of heat loss reduction.

Report describing the best practices for the safe, efficient, and compliant installation of residential air source heat pump water heaters (HPWH) in California, aligning with the state's climate goals and providing guidance for educators, installers, and industry stakeholders.

Web based tool providing decision-making guidance for selecting wall assembly components.

Article describing the control layers (air, thermal, and vapor barriers) needed to build homes successfully in very cold locations.

Information sheet discussing how OSB will define the future of the structural sheathing market. OSB will define the future of the structural sheathing market. - See more at: http://bct.eco.umass.edu/publications/by-title/choosing-between-oriented-strandboard-and-plywood/#sthash.RilEtDpl.dpuf

Installation manual for installing metal panel siding.

An article illustrating common errors found in fiber cement siding installations. Many of these errors and poor flashing examples apply to siding materials beyond fiber cement siding.

Manual assisting architects, engineers, owners and roofing contractors for designing, specifying and installing roof tiles in areas of snow and ice.

Installation manual describing proper installation practices, industry standards and the code requirements of roofing tiles.

Article about how mortar droppings during the installation of a brick veneer can clog the weep holes in the wall assembly causing moisture damage. The article also illustrates products that can be installed in the ventilated cavity to mitigate this problem.

Website providing building science based guidance and training for residential construction.

Article describing research encouraging use of exterior insulation to warm interior sheathing surfaces in walls and roof assemblies to reduce the likelihood of condensation during cold weather

Information about dense pack, cellulose insulation.

Information sheet about what length screws should be used, and how closely to space the screws when fastening furring strips to a foam-sheathed wall.

Factsheet describing ways to install sheathing over existing 1x roof decking.

Checklist describing requirements for roof sheathing along the gable end truss or rafter to achive a FORTIFIED Roof, including New Roof designations and exceptions.

Checklist highlighting key concepts of wind design uplift pressures and design uplift pressure ratings for proper selection and installation of residential roof covering systems to comply with section R905.1 of the 2015 International Residential Code for a FORTIFIED Roof™–New Roof designation.

Checklist providing selection and installation guidance for residential, non-structural metal roof systems installed over wood roof decks with a roof slope 2:12 or greater to comply with section R905.1 of the 2015 IRC for a FORTIFIED Roof – New Roof Designation.

Checklist providing additional guidance and options for asphalt shingle installations at roof edges, intersections and valleys.

Website offering an online training that teaches disaster-resistant best practices for roofers.

Article describing EV charging, charger features, and other considerations for picking and installing EV chargers.

Document that gives a step-by-step approach for designing attachments for cladding materials through foam sheathing.

Factsheet describing how to install air source heat pumps for residential heating and cooling in cold climates.

Factsheet describing how to install air source heat pumps for residential heating and cooling in cold climates.

A article about the best practice method of installing fiber cement siding, to install flashing at the butt joints of the siding boards, rather than face caulking the butt joints afterwards.

Report describing the advantages and best practices for installing heat pump water heaters (HPWH), highlighting their improved energy efficiency, reliability, and critical considerations such as condensate management, proper sizing, and optimal installation location to enhance performance and...

Information sheet presenting techniques for installing cellulose insulation.

Factsheet describing how to partially install a heat pump in a manufactured home in the manufactured home factory.

A guide for users and energy raters of insulated siding as home insulation.

Website providing builders with information about meeting RESNET Grade 1 criteria when installing insulation.

The purpose for this document is to provide basic guidance on the use of proven installation techniques that can be used by installers to help ensure correct “dense pack” application of JM Spider® in drill & fill applications.

Article providing guidance for installing manufactured stone veneer, including information on rainscreens.

Article showing steps for kick out flashing at roof-wall intersection.

Website providing information about Knauf Insulation.

Siding installation guide for Ply Gem Siding Group products.

Discussion of building sheathing.

An article about double-hung windows.

This standard provides a benchmark for safe electrical design, installation, and inspection to protect people and property from electrical hazards and has been adopted in all 50 states.

Report covering wind loading on roofing assemblies.

Information sheet including a checklist of steps to follow for pouring concrete.